Refer attached picture. Kindly check the answer in picture containing the question before submitting the solution. A uniform wire of length 1 800 m and cross-sectional area S= 1.0 mm?is made of a material of density p= 8.0 × 103 kg/m³ and Young's modulusY= 2.0 x 1011 N/m2. The wire is placed straight on a frictionless hori-zontal floor and an end is pulled by a constant horizontal force F= 1.0'N'uniformly distributed over the face of the end. Find displacement ofthis end in a time interval At = 0.1 s after the force is applied.Ans: FAt/sSY = 2-S mum-2.5mn

Answered: Image /qna-images/answer/0980ede7-55f6-48b5-9c5f-ae631604240e.jpg

A uniform wire of length I= 800 m and cross-sectional area S= 1.0 mm² is made of a material of densityp=8.0 x 103 kg/m³ and Young's modulus Y= 2.0 × 1011 N/m2. The wire is placed straight on a frictionless hori- zontal floor and an end is pulled by a constant horizontal force F = 1.0 N'uniformly distributed over the face of the end. Find displacement of this end in a time interval At = 0.1 s after the force is applied. %3D

A uniform wire of length I= 800 m and cross-sectional area S= 1.0 mm² is made of a material of densityp=8.0 x 103 kg/m³ and Young's modulus Y= 2.0 × 1011 N/m2. The wire is placed straight on a frictionless hori- zontal floor and an end is pulled by a constant horizontal force F = 1.0 N'uniformly distributed over the face of the end. Find displacement of this end in a time interval At = 0.1 s after the force is applied. %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shatt carries four masses (150 + 01) kg, (200 + 01) kg, (250 +01) kg and (300 + 01) kg. These masses are located at a distance of 1.5m, 2.5 m, 5.5 mand 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m? and mass density for the shaft material is 7500 kg/m?3. Determine critical speed of the shaft in revolutions per minute for the following two cases: 1. Effect of the mass of the shaft is neglected. 2. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A shaft having length equal to 10 m and diameter equal to (50+ 16) mm is simply supported at both ends. The shaft carries four masses (150 + 16) kg, (200 + 16) kg, (250 + 16) kg and (300 + 16) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A polyethylene bar having rectangular cross section with a width 7.35 in. and depth 7 in. is placed insidea hollow steel square section with side dimension of8 in. The polyethylene bar is then compressed by an axialforce P. At what value of the force P will the gap betweenthe polyethylene bar and the steel tube be closed for thefirst time on one side? What is the remaining gap betweenthe polyethylene bar and the steel tube on the other side?For polyethylene, assume E 5 200 ksi and n 5 0.4.1
A shaft having length equal to 10 m and diameter equal to 70mm is simply supported at both ends. The shaft carries four masses 170 kg, 220 kg, 270kg and 320 kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of magnitude F = 50000 N is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What will be the elongation of the rod (in the unit meters)? Young modulus is 200 × 109 N/m2)" 7.2 x 10-4 3.4 x 10-4 4.6 x 10-4 2.7 x 10-4
An 8.03-kg stone at the end of a steel (Young's modulus 2.0 x 1011 N/m2) wire is being whirled in a circle at a constant tangential speed of 19.8 m/s. The stone is moving on the surface of a frictionless horizontal table. The wire is 4.22 m long and has a radius of 4.94 x 10-3 m. Find the strain in the wire.
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A square plastic bar (length LP,side dimension sp=193 mm) is inserted inside a hollow.square cast iron tube (length Le = 400 mm. side sc=200 mm,and thickness tc=3 mm). (A)What is the required initial length L,of the plastic bar so that.ilcn it is compressed by some force the final length of bar and tube are equal to length L and,at the same time, the gap beten plastic bar and cast iron tube is closed? (B) Compare initial and final volumes for the plastic bar. Assume that E = 170 GP E,= 2.1GPa.v = 0.3.and = 0.4.
A drill string is composed of 5,100 ft of 4½-in. drill pipe with a unit weight of 18 lbf/ft, 300 ft of 4½-in. heavyweight drill pipe with a unit weight of 41 lbf/ft of cross section 6.4023 in2, and 660 ft of 6¼-in. drill collars with a unit weight of 91 lbf/ft. If the drilling-fluid S.G 1,4 and assuming that the WOB is 34,000 lbf. Calculate the axial stress at the top of the hole and at the cross section located 2,000 ft from the top of the hole. Need Solution through 15min
A 540-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 140-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.) (a) Find the (magnitude of the) tension T in the cable.N(b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component _____N vertical component _____N