A utility aircraft has a corner speed of 180 nmi/hr and a maximum structural load factor of n_max = +4.4 g's. What is its allowable load factor at the same altitude but with an of 150 nmi/hr? airspeed 1.2 g's 3.0 g's 3.7 g's 4.4g's O

A utility aircraft has a corner speed of 180 nmi/hr and a maximum structural load factor of n_max = +4.4 g's. What is its allowable load factor at the same altitude but with an of 150 nmi/hr? airspeed 1.2 g's 3.0 g's 3.7 g's 4.4g's O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plane of mass 3000 kg is in level flight at a speed of 300 km/hr with the wings set at an angle of incidence of 3 degrees. If a sharp-edged vertical gust hits the plane with a speed of 30 km/hr, what is the load factor for the plane?
The oil tanker has a smooth surface area of 4.7(1033) m2m2 in contact with the sea. The velocity of the ship is 2 m/sm/s. Suppose that L� = 350 mm . Take ρ� = 1030 kg/m3kg/m3 and μ� = 1.14(10−3−3) N⋅s/m2N⋅s/m2. ( Determine the friction drag on its hull. Express your answer to three significant figures and include the appropriate units. Determine the power required to overcome this force. Express your answer to three significant figures and include the appropriate units.
1. A ship weighing 7200 tons has a KG of 5.20 m, a KB of 3.12 m and a KM of 5.35 m. In the voyage, has used 300 tons of fuel with Kg 0.6 m. If the free surface effect is neglected and assuming KM remains constant, calculate the angle of inclination of the ship.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
The Antonov An-225 is the heaviest aircraft ever built, with a maximum takeoff weight of 640 metric tonnes. It also has the largest wingspan of any aircraft in operational service. Sea level standard day (sls) conditions for calculations are 15°C; 101.3kPa Rotate speed (Vr) at takeoff (sls): Vr = 154 kts = 1.2×Vmin (1 kt = 0.514 m/s) Cruise Engine Thrust : a) Calculate the lift coefficient for a standard day takeoff b) Calculate the drag coefficient at cruis Fcruise = 0.85 Fmax Engine maximum thrust: Factual,max = Fsls,max×δ θ½ δ = Pactual/Pref; and θ = Tref/Tactual
A fuselage with a perfect circular cross-section with a diameter of 3.6 m and a skin thickness of 1.2 mm. Assume a pressure differential while flying at cruising altitude of 45 kPa. Calculate the circumferential stress induced by the pressure differential
A tractor-trailer truck has a drag area CDA = 8 m2 bare and6.7 m2 with an aerodynamic deflector (Fig. 7.18b). Its rollingresistance is 50 N for each mile per hour of speed.Calculate the total horsepower required at sea level withand without the deflector, if the truck moves at (a) 55 mi/hand (b) 75 mi/h.
Suppose you purchase a 4 x 8 piece of plywood from Home Depot. You don't have a pickup truck (nor does your friend), but you do have a roof rack with cross bars on your car. So you will have to secure the plywood to the roof rack in order to get it home. Your friend (the one who does not have a pickup truck) suggests that you tie the plywood on sideways (so that the short edge is front to back) and drive at about 13 mph. Use standard sea-level conditions = 0:0023769 slugs/ft3 and = 3:7372 107 slugs/ft*s.(a) Estimate the drag on the plywood for the case suggested by your friend.(b) Estimate the drag on the plywood if you turn the sheet so that the long edge is front to back.(c) Explain why your friend suggested the sideways configuration
Under non-uniform and slippery road conditions, two forces (u and w), shown in the figure (image 1), are performed on the truck's rear wheels, which have a limited slip rear differential. Choose the alternatives that are true: (data: u = 92lbf and w =57lbf) (obs1.0: 1''= 1 in = 25,4mm) (obs2.0: 1lbf = 4,448N) a) the force vector resulting from the two forces is -149i [lbf] b) the resultant of the two forces has an intensity equal to 149lbf c) the ordinate of the point of intersection of the line of action of the resultant of this system of forces with the y axis is 7.05in d) adopting the counterclockwise direction as positive, the total moment of the two forces in relation to point g is equal to -1050lbf.in e) the total moment vector in relation to the G point is equal to -1050i [lbf.in]
Estimate the rolling resistance force (Fr) for a truck with a mass (M) of 41000kg on a flat asphalt road with a rolling frictional coefficient of 0.033. Assume gravity = g = 9.81 m/sec squared
Task 2:An airplane with a NACA 662-215 airfoil cruises at 170 m/s at an altitude of 4550 m. The airfoil has an aspect ratio of 9 with a span of 30 m. Determine the lift and drag forces then determine the power required to overcome drag. Consider the airplane flying at an angle of attack equal to 2.
An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft