A. 54 rr В. 43 НР C. 33 HP D. 35 HP 11. A three-phase, wye-connected induction motor is connected to a 480 V, three-phase supply. It draws a current of 15 amperes at 80% power factor. A delta connected reactance is connected in , parallel with the motor and the combination draws 15 amperes. What is the value of the element? A. 57.4 µF B. 122.5 µF С. 28.7 F D. 245.0 µF

A. 54 rr В. 43 НР C. 33 HP D. 35 HP 11. A three-phase, wye-connected induction motor is connected to a 480 V, three-phase supply. It draws a current of 15 amperes at 80% power factor. A delta connected reactance is connected in , parallel with the motor and the combination draws 15 amperes. What is the value of the element? A. 57.4 µF B. 122.5 µF С. 28.7 F D. 245.0 µF

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Similar questions

A single-phase alternator connected to 6,600-V bus-bars has a synchronous impedance of 10Ω and a resistance of 1 Ω. If its excitation is such that on open circuit the p.d. would be 5000 V, calculate the maximum load the machine can supply to the external circuit before dropping out of step and the corresponding armature current and p.f. [2864 kW, 787 A, 0.551]
National Power Corporation has A 3-phase, Wye -connected turbo-alternator, having a synchronous reactance of 10 Ω per phase and negligible armature resistance, has an armature current of 220 A at unity p.f. The supply voltage is constant at 11 kV at constant frequency. If the steam admission is unchanged and the e.m.f. raised by 25%, determine the current and power factor. [288.6 A , 0.762 (lag)]
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. a) Draw the single-phase wye equivalent circuit and label all known parameters numericallyincluding load voltage. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
A 3 phase mesh-connected AC generator has a power angle of 15.4 degrees and synchronous impedance of 0.5 + j10 per phase while delivering 300A to its load at a lagging power factor and 13,200 volts line to line. Find the no load emf in volts, line to line.
A wye-connected synchronous motor connected to a 440V, 3-phase line is operating with an electrical load (torque) angle δ of -28 degrees while demanding 90 kW from the mains. The motor has negligible resistance and reactance of 1.5 Ω/ph.Calculate: (a) The line-to-neutral excitation voltage EO(LN) Angle = (b) The line current and power factor.IL Angle = pf =
For one-phase appliance of R-L type (e.g. electrical motor) with active input power P = 10 kW and power factor cosϕ = 0,75 design a power-factor capacitor to compensate the power factor to the standardized value of cosϕk = 0,95. Supply voltage is V = 230 V. Calculate capacitor reactive power, its capacity and current.
Electrical Engineering A wye-connected synchronous motor connected to a 440V, 3-phase line is operating with an electrical load (torque) angle  of -28 degrees while demanding 90 kW from the mains. The motor has negligible resistance and reactance of 1.5 Ω/ph. Calculate: (a) The line-to-neutral excitation voltage (b) The line current and power factor.
Two similar 6600 V, 3-phase alternators are running in parallel sharing equally a total load of 10,000 kW at a lagging power factor of 0.8, the two machines being similarly excited. If the excitation of one machine is adjusted so that its armature current is 438 A, find the armature current and power factor of the second machine if the steam supply is not changed. [Ans. cos Ꝋ2 = 0.568 (lag)]
. A 1,500 kVA, 2300 V, 60 Hz, 3 phase, wye-connected generator has a synchronous impedance of 0.06 + j1 ohms/phase. Field current is 60 A at 125 V dc. Find the percent efficiency of the alternator at full load, 2300 V and 0.9 pf lagging at the above condition. The core and friction losses are 25 kW and 18 kW, respectively
Electromechanical energy conversion (One AC induction motor and one AC synchronous motor were operated connected to an infinite bus of 600V. Power factor of the induction motor is 0,7 (lagging) and consumes 400 W from the bus. Synchronous motor consumes 300 W from the bus. If the power factor of the synchronous motor is 0,9 (lagging) find the line current from the bus, for the total of two motors (IL total 1) of the line that connects the motors with the bus and find the total appearent power (SL total 1) of the motors consumed from the bus. When the induction motor has the same conditions, if the power factor of the synchronous motor is 0,9 (leading) find the line current from the bus, for the total of two motors (IL total 2) of the line that connects the motors with the bus and find the total appearent power (SL total 2) of the motors consumed from the bus.
A Y-connected, 3-phase, 1732 V, 120 kVA, synchronous generator has a synchronous reactance of 1.2 Ω/ph???. Feeds the specified load with pf = 0.9(+) . Fixed losses are assumed to be 5% of developed power. Find: A. The tension generated. b. The power angle. c. Voltage regulation. d. Efficiency. E. Phasor and Power Flow Diagrams