Answered: Air at 1 atm and 20°C flows in a…

Air at 1 atm and 20°C flows in a 3-cm-diameter tube. The maximum velocity of air to keep the flow laminar is (a) 0.87 m/s (b) 0.95 m/s (c) 1.16 m/s (d) 1.32 m/s (e) 1.44 m/s

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.34P

See similar textbooks

Related questions

Q: Air (1 atm) enters into a 5-cm-diameter circular tube at 20°C with an average velocity of 5 m/s. The…

A: Given data as per question Diameter of tube = 5 cm Surface temperature = 160°C outlet mean…

Q: A gas is cooled by circulating it in a turbulent regime through the interior of a circular duct with…

A: Given: The diameter of duct, Di = 0.025 m The internal wall temperature, Ti = 310 K The average…

Q: EXAMPLE 8-1 Laminar Flow in Horizontal and Inclined Pipes Consider the fully developed flow of…

A: Given: The temperature of glycerin, T = 40°C The length of pipe, L = 70 m The diameter of the pipe,…

Q: Q) Water at 22°C flows in a 40-cm-diameter pipe and 25-m-long at an average velocity of 0.15 m/s.…

A: Surface temperature is constant This system contains one fluid is flowing in the pipe and surface…

Q: 4. Compute for the Nusselt value of a forced convection through an elliptical duct at constant Ts,…

Q: A house built on a riverside is to be cooled in summer by utilizing the cool water of the river. A…

Q: Liquid glycerin is flowing through a 25-mm-diameter and 10-m-long tube. The liquid glycerin enters…

A: Internal flow with constant surface temperature We know that q = mCp ( Tmo - Tmi ) Newtons…

Q: Water flows at 1 kg/s in a 10 mm diameter tube and is to be heated from 25 to 75 °C. The tube…

A: INTRODUCTION : When a flowing fluid travels through a heat exchanger, our focus is on either cooling…

Q: For air flow at a constant wall temperature of 100 ◦C and average bulk temperature of 40 ◦C through…

A: Tb=40°CV=0.8m/sD=4cm=0.04m h=?

Q: Consider a 25-mm-diameter and 15-m-long smooth tube that is used for heating fluids. The wall is…

A: Given data as per question Diameter = 25 mm Length = 15 m Mass flow rate = 0.01 kg/s.

Q: Q2: Determine the convection heat transfer coefficient for the flow of (a) air and (b) water at a…

A: Velocity of fluid, V=5m/s Tube diameter, d=8cm=0.08m Tube length, L=10m Case-1 : Air Case-2: Water

Q: Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The…

A: Given information Pressure of air entering = 1 atmTemperature = 60°F = 288.7056 KDiameter of tube =…

Q: asider fully developed flow in a circular pipe with negligible entrance effects. If the gth of the…

Q: Liquid ammonia at -20°C is flowing through a 20-m-long section of a 5-mm-diameter copper tube at a…

A: Write the given information. Write the properties of ammonia at -20°C. Write the expression of the…

Q: Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter…

Q: Water with a mass flow rate of 0.002 kg/s at 18oC flows inside a tube while the flow is already…

Q: Consider a 25-mm-diameter and 15-m-long smooth tube that is maintained at a constant surface…

A: Write the given information. Write the expression of the average temperature.

Q: When the compressibility effects become significant in heat transfer problems in high speed flow

A: The Mach number is used to estimate how close a flow may be considered as an incompressible…

Q: Engine oil at 60ºC (μ = 0.07399 kg/m s, ρ = 864 kg/m3) flows in a 8-cm-diameter tube with a velocity…

Q: Example 1: The components of an electronic system are located in a 1.5-m-long horizontal duct whose…

Q: Glycerin at 40°C with ρ = 1252 kg/m3 and μ = 0.27 kg/m·s is flowing through a 3.5-cm-diameter…

A: Given : The diameter of smooth pipe = 3.5 cm = 0.035 m The average velocity of Glycerin in pipe = 3…

Q: Glycerin at 40°C with r = 1252 kg/m3 and m = 0.27 kg/m·s is flowing through a 4-cm-diameter…

A: The Reynolds number of the flow can be calculated as, Since the determined Reynolds number for the…

Q: Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the…

A: Consider the diagrams shown below for the flow over a cylindrical body. As we can see from the…

Q: Q) Water at 12°C flows in a 2.5-cm-diameter pipe and 10-m-long at an average velocity of 0.1 m/s.…

A: Given: The temperature of water, T = 12°C The diameter of pipe, d = 40 cm = 0.025 m The length of…

Q: For a hydrodynamically and thermally fully developed laminar flow through a circular pipe of…

A: Given: To determine the correct option.

Q: What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The…

Q: Water (5.2 L'min) is flowing in a tube "D-3 cm, L-5 m" and is to be heated from 15°C to 59.9°C by…

A: Given:Volume Flow rate,Q=5.2Lmin=5.2×10-360m3secDiameter,D=3cm=0.03mLength of tube,L=5mInitial…

Q: Q3 Glycerin at 40°C with density of 1252 kg/m³ and viscosity of 0.27 kg/m.s is flowing through a…

A: Find, Pumping power. Pressure drop.

Q: Water flows at 0.2 m/s in a tube of inner diameter 25 mm. Using the water properties below,…

Q: Local Nusselt number for fully developed (hydrodynamically and thermally) turbulent flow in a smooth…

A: Write the given expression of Local Nusselt Number. NuD=A×ReDB×PrC ...... (1)

Q: Using the relationship shown on Fig. 2-6 for heat transfer when a flu flows inside a tube, what is…

Q: Heated air at 1 atm and 100F is to be transportedin a 400-ft-long circular plastic duct at a rate of…

A: Given: The length of the circular duct, L = 400 ft The volumetric flow rate through duct, Q = 12…

Q: Determine the terminal velocity of a 100 mm diameter cylinder, having a length of 360 mm and…

Q: Local Nusselt number for fully developed (hydrodynamically and thermally) turbulent flow in a smooth…

A: Given question: Express the local Nusselt number using Reynold's and Prandtl Numbers in the formNuD…

Q: Q) Water at 22°C flows in a 40-cm-diameter pipe and 25-m-long at an average velocity of 0.15 m/s.…

Q: Water enters a heated circular tube with a diameter of 25.4 mm and a length of 5 m. The water…

Q: Glycerin at 10°C is flowing steadily through a 8-cm diameter pipe at 0.1 kg/s. What is the average…

Q: Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the…

A: Now, consider the value of Reynold’s Number as 3500, the Nusselt numbers are calculated by given…

Q: Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a…

Q: Consider fully developed flow in a circular pipe with negligible entrance effects. If the length of…

A: Given Circular pipe To find Relation of length to pressure and heat transfer

Question

Air at 1 atm and 20°C flows in a 3-cm-diameter tube. The maximum velocity of air to keep the flow laminar is (a) 0.87 m/s (b) 0.95 m/s (c) 1.16 m/s (d) 1.32 m/s (e) 1.44 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Glycerin at 40°C with ? = 1252 kg/m3 and ? = 0.27 kg/m·s is flowing through a 6-cm-diameter horizontal smooth pipe with an average velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe.
Air (1 atm) enters into a 5-cm-diameter circular tube at 20°C with an average velocity of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the outlet mean temperature is 80°C. Estimate the length of the tube.
Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is
Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the Colburn, Petukhov, and Gnielinski equations, determine the Nusselt numbers for Reynolds numbers at 3500, 104, and 5 * 105. Compare and discuss the results.
Determine the expected Fanning friction factor for water at 28 degrees Celsius flowing through a smooth tube whose ID is 15mm, at a velocity of 0.45 m/s
What fluid property is responsible for the development of the velocity boundary layer? For what kinds of fluids will there be no velocity boundary layer in a pipe?
Determine the expected Fanning friction factor for water at 28 degrees Celsius, flowing through a smooth tube with a ID of 15 mm at a velocity of 0.3 m/s.
What is the generally accepted value of the Reynolds number above which the flow in smooth pipes is turbulent?
A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is ?
Someone claims that in fully developed turbulent flow in a pipe, the shear stress is a maximum at the pipe wall. Do you agree with this claim? Explain.