As shown in the figure, a 260-ft tank contains 25 lb of H₂O initially at 30 lbf/in². The tank is connected to a large steam line carrying steam at 200 lbf/in², 450°F. Steam flows into the tank through a valve until the tank pressure reaches p₂ = 160 lbf/in² and the temperature is 400°F, at which time the valve is closed. Step 1 Steam at 200 lbfin². 450°F Am12 = Valve Determine the amount of mass that enters the tank, in lb. lb (1) Determine the amount of mass that enters the tank, in lb, and the heat transfer to the tank from its surroundings, in Btu. Tank Initially 30 lbfin², mi 25 lb (2) Finally P Ibfin² 400°F

As shown in the figure, a 260-ft tank contains 25 lb of H₂O initially at 30 lbf/in². The tank is connected to a large steam line carrying steam at 200 lbf/in², 450°F. Steam flows into the tank through a valve until the tank pressure reaches p₂ = 160 lbf/in² and the temperature is 400°F, at which time the valve is closed. Step 1 Steam at 200 lbfin². 450°F Am12 = Valve Determine the amount of mass that enters the tank, in lb. lb (1) Determine the amount of mass that enters the tank, in lb, and the heat transfer to the tank from its surroundings, in Btu. Tank Initially 30 lbfin², mi 25 lb (2) Finally P Ibfin² 400°F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tank contains R134a initially at 3 degrees Celsius with a quality of 0.25. the pressure is held constant by nitrogen gas acting against a flexible bladder as shown. The valve is opened between the tank and a supply line carrying R134a at 975kPa, 118 degrees Celsius. The pressure regulator allows the pressure in the tank to remain constant as the bladder expands. The valve between the line and the tank closed at the instant when it contains 20kg of R134a with a quality of 0.95. if the entropy generation amounts to 1.025 kj/k, determine: Initial mass of r134a in the tank (kg) Heat transferred (kj) Is heat absorbed or released in the process Show mass, energy and entropy balance equations when starting Initial state, state at inlet, final state H1,s1,h2,s2
A saturated liquid–vapor mixture of water, called wet steam, in a steam line at 1600 kPa is throttled to 50 kPa and 100°C. What is the quality in the steam line? Use data from the steam tables.
As shown in the figure, a 320-ft3 tank contains 25 lb of H2O initially at 30 lbf/in2. The tank is connected to a large steam line carrying steam at 200 lbf/in2, 450oF. Steam flows into the tank through a valve until the tank pressure reaches p2 = 100 lbf/in2 and the temperature is 400oF, at which time the valve is closed.
Saturated liquid R-134a at 24 °C is fed to an adjustable throttling valve that controls the amount of throttling. Analyze the following scenarios:a. The flow is throttled until the exit pressure is 0.32 MPa. Find the exit temperature and quality.b. The flow is throttled to obtain an exit temperature of -12.0 °C. Find exit pressure and quality.c. The flow is throttled until the exit quality is 0.167. Find the exit temperature and pressure. (This will require you to iterate a bit, but you should be able to get a trend by plotting how the quality varies with the temperature for the 3 state points above.)
A boiler takes in feed water at 70 °C and generates steam at a pressure of 10 bar and drynessfraction 0.92. The wet steam enters a superheater and emerges with the same pressure at atemperature of 400 °C. If the steam flow rate is 5 tonnes per hour, determine (i) the rate atwhich heat transfer takes place in the boiler and (ii) the rate at which heat transfer takes placein the superheater. State any assumptions you have made in relation to the steady flowequation for the process.
Two tanks are connected by a valve. Tank 1 has a volume of 40 ft^3 and contains propane at 15 psia and 540 R. Tank 2 of 20 ft^3 has propane at 40 psia and 720 R. If the valve is opened and the propane in both tanks reaches the same state at 620 R, what is the final pressure?
p90#11. ammonia vapor is compressed in a close system from 15 psia,3 cu ft to 150psia,0.4cu ft. according to the relation pV^n=constant. assuming the vapor to be an ideal gas with the gas constant as 90.72 lbm-ft/lbf-Degree rankine and Cv= 0.384 BTU/lbm-degree Rankine compute the heat transferred and the work.
In a natural gas pipe line compressor, 110 m^3/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 degree C. The process follows pV^1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW. And also draw the P-V and T-S diagrams.
Methane is compressed in a two-stage, double-acting compressor which is electrically driven at 165 rpm. The low pressure cylinder (30.5 times 35.5 cm) receives 6.86 cu m per minute of air at 96.53 kPa, 43.3 degree C, and the high pressure cylinder (20.3 times 35.5 cm) discharges the methane at 717.06 kPa. The isothermal overall efficiency is 74%. Find n_v and the kW output of the motor.
A tire develops a slow leak ( assume constant volume) in which the pressure decreases from 50 psia to 40 psia. The area of the hole in the tire is 8(10)-8f2 . The air volume in the tire is 0.6f3 , and the temperature remains constant at 60 degrees F. The mass flow rate of air is given by =0.7 PA / √RT. Determine the time it takes for the pressure decrease. The gas constant R=1716lb/sl/R. The equation of state for an ideal gas is P = pRT
A 2 stage compressor operates between constant pressure limits of 98.6 kPa and 1.103 MPa. The swept volume of the low pressure piston is 0.142m^3. Due to failure of the cooling water supply to the intercooler, air is passed to the high pressure cylinder without reduction in temperature. Using PV^1.2 = C. Determine the percentage increase in power.
Question 3 Consider the turbocharger of an internal combustion engine. The exhaust gases enter the turbine at 450°C at a rate of 0.02 kg/s and leave at 400°C. Air enters the compressor at70°C and 95 kPa at a rate of 0.018 kg/s and leaves at 135 kPa. The mechanical efficiency between the turbine and the compressor is 95 percent (5 percent of turbine work is lost duringits transmission to the compressor). Using air properties for the exhaust gases, determine:(a).The turbine power output, compressor power input, air temperature at the compressor exit,(b).The air temperature at the compressor for the case of isentropic process and isentropic efficiency of the compressor.