The question is related to calculation of strain and is attached as an image. At a particular point in a structural member a two-dimensional stress system exists whereOr = 60 N/mm², o, = - 40 N/mm² and try =50 N/mm². If Young's modulus E = 200 000N/mm² and Poisson's ratio v= 0.3 Calculate the direct strain in the x and y directions andthe shear strain at the point.

Answered: Image /qna-images/answer/e7eea775-945d-488b-9bce-cba350950f5f.jpg

At a particular point in a structural member a two-dimensional stress system exists where Or = 60 N/mm², oy = - 40 N/mm² and txy =50 N/mm². If Young's modulus E = 200 000 N/mm² and Poisson's ratio v = 0.3 Calculate the direct strain in the x and y directions and the shear strain at the point.

At a particular point in a structural member a two-dimensional stress system exists where Or = 60 N/mm², oy = - 40 N/mm² and txy =50 N/mm². If Young's modulus E = 200 000 N/mm² and Poisson's ratio v = 0.3 Calculate the direct strain in the x and y directions and the shear strain at the point.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Related questions

Q: 4. Given a shear stress of T-35 MPa and a shear modulus of G= 75 GPa, the shear strain is most…

A: Given data Shear stress=35 mpa Shear modulus =75 gpa We have to determine shear Strain

Q: F 30° ød. 2 M. 10

Q: Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading…

A: It is assumed that Compressive stress developed in the top section. Also tensile stress in the…

Q: A cube of side 40 mm, subjected to 3 mutually perpendicular tensile forces of 9 kN, 5 kN, 5 kN…

Q: A roadway sign weighs 5.4 kN and is supported by a structural pipe that has an outside diameter of…

Q: 2.44.The distribution of stress in a structural member is given (in megapascals) by Eqs. (d) of…

Q: v) A delta strain gauge is attached to the member at point ‘X’ as highlighted in the figure. During…

A: The magnitude of strain at an angle is given by:εθ=εx+εy2+εx-εy2cos2θ+γxy2sin2θAt…

Q: Homework :-in the figure shown. Find the total deformation and the stress in each section if E is…

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A sheet of material is subjected to a two-dimensional stress system in the x-y plane. At a given…

Q: If the principal stresses in a plane stress problem are ơ1 = 100 MPa, ơ2 = 40 MPa, the magnitude of…

A: Write the given values along with suitable variables.

Q: Find the strains in the 1-2 coordinate system (local axes) in a unidirectional boron/epoxy lamina…

A: Given data: Standard data for boron/epoxy is

Q: Calculate the principal strains and stresses, the maximum shear stress, and the orientation angle…

A: Given that: Strain gage rosette type is delta rosette. Measurements are: ε1=400 μm/m ε2=84 μm/m…

Q: Determine the principle stresses σ1, σ2, σ3 and their orientation φ, if σx, σy and σz are known as…

Q: If the principal stresses in a plane stress problem, are o1 = 100 MPa, o2 = 40 MPa, the magnitude of…

Q: The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to…

A: Given, εx = 139 x 10-6 E = 204 GPa ν= 0.3

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Need to determine normal stress σn or ( σx ) In the given answer normal stress is shown by σn Data…

Q: Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point…

A: Given data: The direct stresses in mutually perpendicular direction are σx=120 Nmm2 and σy=-90…

Q: 800 N D 120 N.m d = 8 cm 600 N Q / If the cross section of the femur can be approximated as a…

A: 1. Stress due to eccentric load of 800N P2 and 800N will create a momentMoment due to this…

Q: The principal stresses at a point are : 40 MPa, 30 MPa and - 20 MPa. Calculate per unit volume the…

A: We know the main stresses at a place are known to be 40 MPa, 30 MPa, and -20 MPa. Total strain…

Q: A recently developed Afordium, a new, inexpensive alloy for use in the d. the normal stress in…

A: Given that , AB=600mmBC=400mmAAB=7.5×10-4m2ABC=3×10-4m2

Q: A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa,…

A: Given data Internal diameter of steel cylinder (Di) = 160 mm internal radius (ri) = 80 mm outer…

Q: A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress…

A: The strain values are given as, ε1=121×10-6ε2=304×10-6ε3=203×10-6 The Poisson's ratio is given…

Q: The total volume of inherent strain longitudinal direction is Vx = Kq. H

A: we are discussing a theoretical model to determine the volume of inherent strain in longitudinal…

Q: 1: The forces as given below are applied as shown in the figure. Fi=10 kN, F2=5 kN and F3=3 kN. The…

Q: When there is a plane stress condition as shown in the figure, display this stress in the form of…

Q: the nodal displacements are For the plane strain elements shown in the Figure given as (4, 4) uj =…

A: Solution: Given Data:

Q: The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a…

A: (a) To find: The axial force F in the ring in terms of p, w and r; Calculation: Consider a FBD by…

Q: Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a…

Q: In the picture below, the beam AB is held up by cable BC on the right at B and supported by a pin on…

Q: Q.2. A bar of different cross sections is subjected to a tensile force of 50 kN. Find the stresses…

A: Given data: F = 50 kN Need to determine the stress and stretch in each section of the given bars.

Q: Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at…

A: Given: The length of the bar→L=100 mm=0.1 m Diameter of the bar→d=15 mm=0.015 m At point A: Because…

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: For the state of stress shown in the figure, determine the stress component Txy so that the maximum…

Q: the principal stresses at a point H on the surface of the vessel and the absolute maximur shear…

Q: 3. Evaluate the longitudinal residual stress along the X-direction for 4mm width of tension at a…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

Q: Part 1 A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: The plate shown in Figure is fixed connected along with AB and held in the horizontal guides at its…

A: When the plate is deformed then in that case the diagonal AC becomes AC'. Then from the pythagoreous…

Q: Determine the principle stresses and the maximum in-plane shear stress.

Q: 3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

Q: Determine the absolute maximum shear stress of the stress state acting on the element shown in the…

Q: A structural plate shown in the figure is deformed into the shape represented by the dashed line.…

A: Normal strain is the deformation occurred in the body due to the application of normal force. Shear…

Q: Try

A: Given Data : σx=60 MPa σy = 0 τxy = 40 MPa.

Q: O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall…

A: Given: The outer diameter of the steel cylinder is D = 360 mm. The inner diameter of the steel…

Q: 10 The stress components at a point are given by : Ox = Oy = 0z = 50 MPa, txy = 10, tyz = 20, T = 15…

Question

The question is related to calculation of strain and is attached as an image.

At a particular point in a structural member a two-dimensional stress system exists where
Or = 60 N/mm², o, = - 40 N/mm² and try =50 N/mm². If Young's modulus E = 200 000
N/mm² and Poisson's ratio v= 0.3 Calculate the direct strain in the x and y directions and
the shear strain at the point.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
An element of a material is subjected to plane stresses as shown in the figure. The stresses o, cry., and are 10 MPa, —15 MPa, and 5 MPa. respectively. Assume E = 200 GPa and v = 0.3. (a) Calculate the normal strain in the x, v. and z directions and the shear strain. (b) Calculate the strain-energy density of the element.
Solve the preceding problem if the plate is made of aluminum with E = 72 GPa and Poisson’s ratio v = 0.33. The plate is loaded in biaxial stress with normal stress sx= 79 MPa, angle Ø = 18°, and the strain measured by the gage is e = 925 × 10-6.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.