Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading conditions of two vertical forces that applied on it. The beam has cross section as shown in figure. | 100KN |100KN 200 mm D. 25 mm 25 m 150 23 mm 1500 mm 500 mm 500 mm 100 mm

Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading conditions of two vertical forces that applied on it. The beam has cross section as shown in figure. | 100KN |100KN 200 mm D. 25 mm 25 m 150 23 mm 1500 mm 500 mm 500 mm 100 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.31P: Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the...

See similar textbooks

Related questions

Q: A roadway sign weighs 5.4 kN and is supported by a structural pipe that has an outside diameter of…

Q: A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside…

A: Calculate the moment about point H due to load P. MH=P370 mm×1 m1000 mm=22 kN×1000 N1 kN370 mm×1…

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36…

Q: 1- The normal and shearing stresses at point K 2- Sketch the results on a differential volume…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: To find: The state of stress at point A on the cross section of pipe at section a-a. Given: The…

Q: Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile…

A: Concept Of Moment Inertia Used

Q: Determine the maximum stresses in the stepped shaft composite of two materials steel and Aluminum…

A: Given; GS=82 GPaGAl=27 GPa

Q: 1.2 A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter…

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: GivenAxial load P=115.33kNT section cantilever beam as shown below

Q: Two vertical forces, each of magnitude P= 26 kips, are applied to a beam of the cross section shown.…

Q: 3. Compute the shear stresses. At the top of the side wall the thickness, 1, is 24 in. The torsional…

Q: Two vertical forces, each of magnitude P= 28 kips, are applied to a beam of the cross section shown.…

A: First, we calculate the moment of inertia of the given section: The section converted into three…

Q: The wide-flange beam is subjected to the P = 54 kN force. Determine the principal stresses in the…

A: Drawing the FBD of the given schematic diagram,

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given: The load is 115.33 kN. The T cross section is shown below:

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given Data: The load acting on the beam is P=115.33 kN. The eccentricity from the neutral axis is…

Q: Two bars are connected by means of a rivet of diameter 5 mm as shown in fig. below. Determine the…

Q: - 540 mm 180 mm- 180 mm 60 mm → - B 30 kN

Q: Su The curved member is symmetric and is subjected to a moment M. bending stresses, both tension and…

Q: 10/10FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70…

Q: 1. Determine the stresses for a square stress element on top of CD at point D. The stress element is…

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

A: Let's find distance of H.C.A of T- cross section from bottom Y—=A1Y1—+A2Y2—A1+A2=18×1+18×518+18=3…

Q: 1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in…

A: It is asked to find the stress generated in the bars due to temperature change

Q: Que 1.23. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external…

Q: 3 in. 3 in. 3 in. Two vertical forces are applied to a beam of the cross section shown. Determine…

Q: QUESTION 1 A Z-section beam of 2 m long and is supported as a cantilever with a 1 kN load at the…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D + ,…

A: Given, tEDC = 10 mmwEDC = 50 mmtAD = tBC = 8 mmwAD= wBC = 36 mmd = 16 mmF = 20 kNLAD = LBC = 0.2 m…

Q: 0.8 m 0.4 m В 0.6 m 1.6 m P = 1.2 kN 2 m The rigid beam AB is hinged to a support at A and supported…

A: Suppose angular displacement of beam is δθ; then, stretch in wire C and D are 0.6 x δθ & 1.6…

Q: Q2 Determine the maximum tensile stress of the beam with details shown in Figure 2. 48 kN 60 kN 60…

Q: QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point…

A: The section is as shown below, The area of the section is, A1=20×5=100 cm2A2=20×5=100…

Q: For the I section shown in figure. If the section is subjected to a shear force of 120 kN, determine…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: re= 3cm 300m 20m

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of…

Q: Example 3 Determine: a. The shear stress at point B on the web of the cantilevered strut at section…

A: Answer: (a) The shear stress at point B: 8.81735 MPa (b) The maximum shear stress: 9.70434 MPa

Q: · Three forces are applied to the structure shown in Figure 3. Determine the maximum possible normal…

A: Given: Fy=-0.5 kNFx=-3 kNFz=-2.5 kN

Q: Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at…

A: Given: The length of the bar→L=100 mm=0.1 m Diameter of the bar→d=15 mm=0.015 m At point A: Because…

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: An overhanging beam of channel section supports a uniformly distributed load of 10 kN/m and a…

A: Given: The UDL, w = 10 kN/m The concentrated load, P = 20 kN

Q: Two vertical forces, each of magnitude P= 14 kips, are applied to a beam of the cross section shown.…

A: The question is related to the normal bending stresses produced in the beam due to bending only. The…

Q: Dmm Ø20 0,1 Ø10 20 2. Draw diagram of normal stresses.

A: Here bending stresses will be normal stresses. The normal stresses diagram drawn in step 2.

Q: G.2 kN 1.25m 90 mm I20 mm 30 mm 3.2 m 80 mm

A: Given: The value of load is, P=6.2 kN. The length of the beam is, L=3.2 m. Assumption: Point C…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Write the expression for the change in length. Here, P represents the load, L represents the…

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

A: Given Data: The load acting on the beam is 25 kip each. The free-body diagram of the beam can be…

Q: Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading…

Q: O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall…

A: Given: The outer diameter of the steel cylinder is D = 360 mm. The inner diameter of the steel…

Q: (a) Determine the maximum tensile stress and maximum compressive stress o (in MPa) due to the load P…

Q: Calculate the principal stresses o 1 at point A of cross-section aa. Data: L = 0.3 m; F = 0.9 kN.…

Q: Question 1) F=22 kN single load, M-24 kN.m moment and w=5 kN/m distributed load act on the beam…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Determine the maximum tensile and compressive stresses in portion BC
of the beam, under loading conditions of two vertical forces that applied
on it. The beam has cross section as shown in figure.
100KN
| 100KN
200
mm
25 mm
25 mm
150 um
25 mm
1500 mm
500 mm
500 mm
100 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
A short column with a wide-flange shape is subjected to a compressive load that produces a resultant force P = 55 kN acting at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses asand o^., respectively, in the column, Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a 120 mm X 10 mm cover plate is added to one flange as shown.
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a