At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/kg. In addition, the velocity is 50 ms. At the discharge end, the enthalpy is 2600 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at the exit of the nozzle? b. If the inlet area is 900 cm and specific volume at the inlet is 0.187 m/kg, find the mass flowrate? c. If the specific volume at the exit of the nozzle is 0.498 m'kg, find the exit area of nozzle? Fhid in -Fhaid out V- 50 m's A- 900 em hi- 2800 kkg h:- 2600 kkg

At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/kg. In addition, the velocity is 50 ms. At the discharge end, the enthalpy is 2600 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at the exit of the nozzle? b. If the inlet area is 900 cm and specific volume at the inlet is 0.187 m/kg, find the mass flowrate? c. If the specific volume at the exit of the nozzle is 0.498 m'kg, find the exit area of nozzle? Fhid in -Fhaid out V- 50 m's A- 900 em hi- 2800 kkg h:- 2600 kkg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a liquid jet which is coming out from a small hole areaof cross section S with velicity q1 and making an angle A with the horizon. Find the velocity of the liquid at point 2?
A jet of water having a velocity of 45 m/s impinges without shock on a series of vanes moving at 15 m/s. The direction of motion of the vanes is inclined at 20° to that of the jet, the relative velocity at outlet is 0.9 of that at inlet, and the absolute velocity of the water at exits is to be normal to the motion of vanes. A) Find the Blade angle at entrance B) Find the Blade angel at exist c)Find the work done on the vanes, in Newton-meter, per kilogram of water supplied by the jet;
Water flows through the reducer, the inlet diameter is 20 cm and the outlet diameter is 10 cm. If the velocity at the inlet is 0.4 m/s and the pressure 107, what is the pressure in kPa at the exit? Assume frictionless flow with no heat loss.
The pressure of the water base of a Pelton Wheel is 4850 kPa and the velocity at the same point is 6 m/s. The jet diameter is 20 cm, and the velocity coefficient is 0.98 and the turbine’s efficiency is 86%. Find the brake power, in bkw.
A pump delivers gasoline at 20°C and 12 m3/h. At the inletp1 =100 kPa, z1 = 1 m, and V1 = 2 m/s. At the exit p2 = 500 kPa, z2 = 4 m, and V2 = 3 m/s. How much poweris required if the motor efficiency is 75 percent?
In Fig. the pipe entrance is sharp-edged. If the fl ow rateis 0.004 m3/s, what power, in W, is extracted by the turbine?
A hydro-electric plant discharge water at the rate of 0.75 m3/s and enters the turbine at 0.35 mps with a pressure of 275 kpa. Runner inside diameter is 550 mm. Speed at 320 rpm and the turbine efficiency is 88%. Find the turbine speed factor.
A fluid enters with a steady flow of 3.7 kg/s and an initial pressure of 690 kPa, an initial density of 3.2 kg/m3, an initial velocity of 60 m/s, and an initial internal energy of 2000 kJ /kg. It leaves at 172 kPa, ρ = 0.64 kg/m3, v = 160 m/s, and u = 1950 kJ/kg. The heat loss is found to be 18.6 kJ /kg. Find the power produced or required by the system.
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%?
b. The discharge pressure of an air compressor is 6 times the suction pressure. If the volumeflow rate at the suction is 0.86 cubic meters per second, what is the compressor power (kW)for n = 1.38 and suction pressure is 101 kPaa?
When the pump in Fig. P3.169 draws 220 m 3 /h of water at20 ° C from the reservoir, the total friction head loss is 5 m.The flow discharges through a nozzle to the atmosphere.Estimate the pump power in kW delivered to the water.
Water is flowing in a convergent duct. In one area, the diameter is 14 cm. If the velocity there is 12 m/s. (a) Find the mass flow rate.(b) At a station down the duct, the diameter is 2.5 cm. Find the velocity at this station. *If answer is submitted without a solution, it will not be considered.