(b) During a course of Integrated Engineering Design, your group project's design requires a high torque motor to execute the desired task. The project would use a motor that has an equivalent circuit as in Figure 1. Based on the two motors listed in Table 1, choose the one that have higher torque to fulfil the requirement of your Integrated Engineering Project's design. Justify your answer by showing all the calculation details. R. R ME Figure 1 Table 1 Parameters HS85013119 HS850136480 Rated terminal voltage / V 230 200 Rated current / A 35.7 38 Field resistance / m? 50 50 Armature resistance / m2 25 25 Rated speed / rpm 1200 1000 Stray losses / W 200 + x00 200 + x00 Where x is

(b) During a course of Integrated Engineering Design, your group project's design requires a high torque motor to execute the desired task. The project would use a motor that has an equivalent circuit as in Figure 1. Based on the two motors listed in Table 1, choose the one that have higher torque to fulfil the requirement of your Integrated Engineering Project's design. Justify your answer by showing all the calculation details. R. R ME Figure 1 Table 1 Parameters HS85013119 HS850136480 Rated terminal voltage / V 230 200 Rated current / A 35.7 38 Field resistance / m? 50 50 Armature resistance / m2 25 25 Rated speed / rpm 1200 1000 Stray losses / W 200 + x00 200 + x00 Where x is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

SPEED CONTROL OF A DC MOTOR BY FIELD CONTROL A dc shunt motor is taking 20 A from the 220-V source. The field and armature resistances are 110 ohms and 1 ohm, respectively. Find the the value of an external resistance connected series to the field winding that will cause the speed of the motor to double while taking the same amount of current from the source. Draw the schematic of the motor before and after the application of an external field resistance.
Q4: Briefly describe how the speed varies as the mechanical load applied to the squirrel-cage induction motor increases, i.e. as the motor torque increases.
A series-connected dc motor is designed to operate with a variable load. The resistances RA and RF are negligible. To attain high efficiency, the motor has been designed to have very small rotational losses. For a load torque of 100 Nm, the machine runs at its maximum rated speed of 1200 rpm. a. Find the speed for a load torque of 300 Nm. b. What is the no-load speed? What are the potential consequences of having the load become disconnected from the motor without disconnecting the dc source?
A DC Series motor, 500V, has a total resistance of 0.5 Ω. At plain load, the current is 100 A at a speed of 6 rev / s. At reduced load, the current is 50 A with a speed of 10 rev / s. Consider that the torque is proportional to the current on this scope. What is the current of the motor when the induced torque is 786 N·m? What resistance value should be added so that the speed is 6 rev / s at 786 N·m?
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. the ratio of emf at no load to full load
An AC induction machine has six poles and isdesigned for 60-Hz, 240-V (rms) operation. When themachine operates with 10 percent slip, it produces60 N-m of torque.a. The machine is now used in conjunction with an800-W constant power load. Determine the speedand slip of the machine when used with theabove-mentioned load.b. If the machine has an efficiency of 89 percent,what minimum rms current is required foroperation with the load of part a?Hint: You may assume that the speed–torque curve isapproximately linear in the region of interest.
440V shunt DC motor has an armature resistance of 1.2Ω and field resistance of 300Ω. find the back emf when giving an output of 10kW at 89% efficiency a) find the back emf mathmatically
Draw the approximate equivalent (without Xm) circuit of an induction motor and derive the equation of the maximum torque..
An induction motor of 30 HP, 220 V, 450% of the rated current with therated voltage and delivers during the starting period, with 130 % of the normal torque. The full load efficiency and full load power factor of the motor is 80 and 70 percent, respectively. If an autotransformer is used as a starting unit and the starting torque of the load is only 50 % of the rated torque of the motor, Determine the starting voltage and the starting current of the line.
A four pole DC shunt motor moves at 1000rpm on a 460v supply when taking an armature current of 45A. Annature resistance is 0,400hms, find the torque developed by the motor if the field circuit remains at 460V.
A 50MVA, 11kV salient pole machine having a direct‐axis reactance of 0.8pu and a quadrature‐axis reactance of 0.6pu. The machine is connected to an infinite bus having a voltage of 11kV and supplying 40MW at 0.8 lagging power factor. Determine the power angle, the voltage proportional to field current, the direct axis and the quadrature‐axis components of the voltage and current. The load angle and the excitation voltage at which the maximum power transfer occurs.
A 40-HP, 230-V., 8-pole, 25 Hz three-phase induction motor is running at 355 rpm at rated load. The torque lost by friction is 24 N-m. If the stator losses amount to 1,000 W., calculate the efficiency of the motor at this load.