Moment (KN.m)3002502001501005000AMoment-Curvature Relation0.01 0.02 0.03 0.04 0.05 0.06 0.07Curvature (1/m)Lb) Yield displacement (Ay).Ay=Calculate the following values:a) Yield Force (Fy) that will cause the system to yield at point A.Fy=c) Plastic displacement (Ap).Ap=Hint: Au Ap+Ay=Başka yönergeler almak için tıklayınFor the cantilever beam system given, construct the relation between the force (F) and the displacement (A) of the free end. You need to transform the moment curvature relation given into force-displacement relation.Beam length: L = 3.5 mPlastic hinge length: Lp = 0.3 mNote: All the results are positive.Fe) The ultimate (failure) force (Fu)Fu =d) Ultimate (failure) displacement (Au).Au=(m)0.08 0.09(m)FAhaAyAu(KN) (Write 2 digits after the decimal point)(m) (Write 4 digits after the decimal point)(Write 4 digits after the decimal point)(Write 4 digits after the decimal point)A(KN) (Write 2 digits after the decimal point)

A cantilever beam with point load, F and moment curvature relationLength of the beam, L =3.5 mLength…

Calculate the following values: a) Yield Force (Fy) that will cause the system to yield at point A. Fy= b) Yield displacement (Ay). Ay= c) Plastic displacement (Ap). Ap= (KN) (Write 2 digits after the decimal point) (m) (Write 4 digits after the decimal point) (m) (Write 4 digits after the decimal point) d) Ultimate (failure) displacement (Au). Au= (m) Hint: Au= Ap+Ay e) The ultimate (failure) force (Fu) Fu= (Write 4 digits after the decimal point) (KN) (Write 2 digits after the decimal point)

Calculate the following values: a) Yield Force (Fy) that will cause the system to yield at point A. Fy= b) Yield displacement (Ay). Ay= c) Plastic displacement (Ap). Ap= (KN) (Write 2 digits after the decimal point) (m) (Write 4 digits after the decimal point) (m) (Write 4 digits after the decimal point) d) Ultimate (failure) displacement (Au). Au= (m) Hint: Au= Ap+Ay e) The ultimate (failure) force (Fu) Fu= (Write 4 digits after the decimal point) (KN) (Write 2 digits after the decimal point)

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m , h=7m , b=5 m) I need a solution within 40 min
A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in diameter. If 2 liters of water per minute flow upwards through the pipe the pressure difference across the pipe is 35 kpa. Calculate the flow downwards through the pipe if the pressure across the pipe is to be zero. The losses across the pipe are given by h1=k((v2) ²-(v1)²)/2g,where v1 and v2 are the velocities in the 50 mm and 25 mm sections respectively.
The rectangular bin with an inclined gate AB is filled with oil to the depth shown. Determine the resultant force (kN) acting on the inclined side AB. Take density of oil - 900 kg/m^3 x=3.27 a=5.2 m b=30 degrees asap
The piston at A has a cross sectional area of 700 sq.cm. while that of B is 120 sq.cm.as shown in figure. The difference in elevation between pistons A & B is2.3meters. If the intervening passages are filled with oil (S=0.8), what force P in kn isrequired to maintained equilibrium?
The rectangular bin with an inclined gate AB is filled with oil (SG 0.8) to the depth shown. Determine the resultant force (kN) acting on the inclined side AB. Take density of glycerin = 2650 kg/m^3 x = 2.2 m a = 2.3 m b = 30 degree
In the cage system given in the figure, AB, DE andPressure or pull CB rod forcescalculate by stating that they are. L1(m)=2.1 ,L2(m)=3.2, P1(kN)=65, P2(kN)=57
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical position (?= 90°) where the attached spring of stiffness k = 4.3 lb/in is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity ? = 5.9 rad/sec as the lever reaches the horizontal position ? = 0.
Figure Q2 shows a reinforced concrete platform with a cantilever slab and wall at the edge of slab. The brick wall is seated on the edge of cantilever slab is 3.2 m high. Given: All slab thickness = 150 mm All beams = 250 mm × 600 mm Concrete unit weight = 25 kN/m3Weight of brickwall = 2.6 kN/m2Finishes = 1.5 kN/m2Variable action = 5 kN/m2 Determine the characteristic permanent action (gk in kN/m) and variable action (qk in kN/m) acting on Beam B/1-2.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=22ft. A.) The hydrostatic force due to linseed oil F1. B.) The hydrostatic force due to castor oil F2 C.) The hydrostatic force due to water. D.) The net hydrostatic force acting on the gate Fnet.
Fluid Mechanics Problem 1) A rectangular gate 3 meters high and 1.2 meters wide is hinged at the top. A force to keep the gate closed is applied at the bottom with an angle of 45 degrees with the veritcal. Compute the following if the water surface is 0.9 meters below the top of the gate. Use 9.81kN/m^3 as water's specific weight. a. the total hydrostatic force acting on the gate in kN. b. the distance of the total hydrostatic force measured from the liquid surface in meter. c. the magnitude of the force at the bottom of the gate in kN. 2) Use 9.81kN/m^3 as water's specific weight. Consider the rectangular gate shown in the figure. If the gate has a length of 2 meters, determine: a. the force exerted by the water on the left side of the gate in kN. b. the force exerted by the water on the right side of the gate in kN. c. the horizontal force at B required to turn the gate about the hinge in kN.