Calculate the new injector size (Ib/hour) and also the new engine power, Peng [Watt] of an engine if the fuel pressure (fuel pump) is increased to 100% from the current pressure. Others data of the engine are as below: Cylinder number = 4, natural aspirated SI engine, EFI system Current fuel pump pressure = 35psi Injector fuel flow rate = 180 c.c

Calculate the new injector size (Ib/hour) and also the new engine power, Peng [Watt] of an engine if the fuel pressure (fuel pump) is increased to 100% from the current pressure. Others data of the engine are as below: Cylinder number = 4, natural aspirated SI engine, EFI system Current fuel pump pressure = 35psi Injector fuel flow rate = 180 c.c

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

State what is Bernoulli's Priciple for Pressure and Velocity? In 8 sentences only.
Calculate the speed of sound for the U.S. standard atmosphere using c = √kRT , where c represents the speed of sound in m/s, k is the specific heat ratio for air (k = 1.4) , and R is the gas constant for the air (R = 286. J/KG · K ) and T represents the temperature of the air in kelvin. The speed of sound in atmosphere is the speed at which sound propagates through the air. You may use Excel to solve this problem.
After graduation, you work for a pump manufacturing company. One of your company’s best-selling products is a water pump, which we shall call pump A. Its impeller diameter is DA = 6.0 cm, and its performance data when operating at n. A = 1725 rpm (?A = 180.6 rad/s) are shown in Table.The marketing research department is recommending that the company design a new product, namely, a larger pump (which we shall call pump B) that will be used to pump liquid refrigerant R-134a at room temperature. The pump is to be designed such that its best efficiency point occurs as close as possible to a volume flow rate of V. B = 2400 cm3 /s and at a net head of HB = 450 cm (of R-134a). The chief engineer (your boss) tells you to perform some preliminary analyses using pump scaling laws to determine if a geometrically scaled-up pump could be designed and built to meet the given requirements. (a) Plot the performance curves of pump A in both dimensional and dimensionless form, and identify the best…
i. A wind turbine has the following data: Downstream wind velocity = 9 m/s Upstream wind velocity =18 m/s Rotor Power output = 1 MW a. Compute the wind rotor efficiency. b. Calculate power in the wind and the length of the rotor blades ii. ComparethedifferenttypesBiogasplants?
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
The wind turbine gives the following data: Blade length, l = 39 m, Wind speed, V= 12.4 m/s, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.39, Calculate the power available in the wind.
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
A centrifugal pump, pumps water at 0.240 m3/s rotating at 1200 rpm, a prototype pump using 10 lit/s is to be tested. If the diameter of the model is 3 times the diameter of the prototype, at what speed should the prototype run, if the pump pumps oil at a head of 30 meters. (a)What would be the required horsepower to drive the model at an efficiency of 0.8? (b)What would be the required horsepower to drive the prototype?
a. CH, CQ and  are functions of CP. Draw the dimensionless performance curves of the turbine on a single graph by makingthe necessary scalings. (Fit the curve by using the excel program for drawing. Also give the values you used for plotting inthe table) b. Find the efficiency of the model at the most efficient operating point and the coefficients of head (CH), flow (CQ) and power(CP). Show them on the graph you have drawn. c. Calculate the diameter, net head, number of revolutions (rpm), flow rate, power (MW) and modified efficiency of theprototype d. Determine the turbine type ÖN number is 5
2. The specific speed of a turbine is 85 rpm and running at 500 rpm. What is the maximum power, in HP, delivered by the generator if the head is 25 m and generator efficiency is 90 %. Copy the problem, then show Complete Solution/s (i.e. transformations, equivalent formula, etc).