Answered: Calculate the volume of 0.08640M EDTA…

Science

Chemistry

Calculate the volume of 0.08640M EDTA needed to titrate a 25.00-mL aliquot of this solution.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter17: Complexation And Precipitation Reactions And Titrations

Section: Chapter Questions

Problem 17.19QAP

See similar textbooks

Related questions

Q: The amount of calcium in physiologic fluids can be determined by a complexometric titration with…

A: EDTA( Ethylene diamine tetraacetic acid) is a very large molecule and a chelating agent. It forms…

Q: Molarity of Na2S2O3 (stock solution). 0.100 M Volume of diluted bleach titrated (taken from the…

A: Density of commercial bleach solution = 1.08 g/mL

Q: What is the correct order of performing EDTA titration? I. Titrate milk sample aliquot with standard…

A: Steps for performing EDTA titration Weighing Preparation of standard solution Standardization of…

Q: 50.00 mL of a solution containing iron (II) and iron (III) when titrated at pH2.0, 12.50 mL 0.01200…

A: Answer is explained below. From the given plot it is clear that at ph = 2.0, only Fe3+ reacts with…

Q: 6mL of 125mM EDTA was added to 244mL of water. The resulting solution was added to 219mL of water…

A: MW of EDTA =292.24 g initial molarity of EDTA = 125mM

Q: Determine the molarity of the 10.00 mL standard EDTA solution titrated using 1.000 g zinc sulfate in…

Q: Calculate the molar solubility of Ni(OH)2 (Ksp = 2.0 × 10-15) in a solution which is buffered at pH…

A: Ksp of Ni(OH)2 = 2.0×10-15 pH = 9.75 Using relation: pH + pOH = 14 pOH = 14 - pH = 14 - 9.75 =…

Q: 5. 20 mL of tap water sample is taken in a conical flask and 1 mL of pH 10 buffer and 3 drops of…

A: Hard water is the water that contains dissolved Ca2+ and Mg2+ ions. These ions react with fatty…

Q: 7. A solution contains 1.569 mg/mL of CoSO4(MM = 155.0 g/mol). Calculate the volume of 0.007840 M…

A: Given data, Q7) Concentration of CoSO4 = 1.569 mg/mL Molar mass of CoSO4 = 155.0 g/mol Concentration…

Q: Molarity of Na2S2O3 (stock solution). 0.100 M Volume of diluted bleach titrated (taken from the…

A: Solution: For a given titration reaction the stoichiometric relation plays important role, as from…

Q: Determine the molar concentration of an EDTA solution of which 26.44 mL were required to titrate a…

Q: When doing a titration, it is helpful to know approximately the volume of titrant that will be…

A: The equation to calculate the unknown value from known value is given by, M1V1=M2V2 where M is the…

Q: If 10.00 mL sample of 0.01 M standard Ca2+ solution is titrated with 9.8 mL of EDTA solution, what…

A: Interpretation - To determine the molarity of the EDTA when 10.00 mL sample of 0.01 M standard Ca2+…

Q: 1. A solution contains 1.238 mg of CoSO4 (155.0 g/ mol) per milliliter. Calculate the volume of…

A: Here we are required to find the molar concentration of EDTA.

Q: A student titrated a 25.00 mL sample of water with 0.0200 M EDTA. The titration required 20.40 mL of…

A: This is a simple volumetric titration, using M1V1=M2V2 we can obtain the strength of water sample.…

Q: What is the MW of calcium carbonate?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Calculate the volume of 0.0500 M EDTA need to titrate 25.6 mL of 0.0600 M Mg(NO3)2.

A: EDTA is ethylenediaminetetraacetic acid which is an indicator. It has 2 amino and 4 carboxyl groups.…

Q: 50.00 mL of a solution containing iron (II) and iron (III) when titrated at pH2.0, 12.50 mL 0.01200…

A: Option B should be the correct answer. We know that the metal ion which is titrated without…

Q: At 40.0 mL 0.0050 M Sr2 + pH 10, 0.0100 M EDTA is titrated. Calculate the pSr for the equivalence…

A: We have been given a Strontium solution whose concentration and volume is known. we need to…

Q: Mass of NaOCl in commercial bleach titrated. ?

A: Moles help to calculate mass

Q: Calculate the concentration of an EDTA solution of which 24.22 mL were needed to titrate the Ca2+…

A: Given: Volume of EDTA solution used = 24.22 mL = 0.02422 L…

Q: A sample of pure CaCO3 weighing 0.3677g is dissolved in hydrochloric acid and the solution diluted…

A: According to the mole concept, in terms of mass, the amount of substance in moles is equal to the…

Q: According to the following figure, an adequate end-point for the titration of calcium with EDTA…

A: End point is the point where the indicator changes colour and we know that this point Comes after…

Q: Consider the titration of 25.00 mL of 0.03555 M Co2+ by 0.02784 M EDTA at pH 10.00. Kf is 1045.…

A: The amount of EDTA required to reach the endpoint of the titration is determined as shown below.…

Q: Titration of 0.2121 g of primary standard NagC;0, Calculate the molar concentration of KMnO,? 2…

Q: The Zn in a 260-g sample of foot powder was titrated with 2 L of 0.5 M EDTA. Calculate the percent…

A: Given that - Mass of Sample of Zn = 260 g Volume of EDTA Solution = 2 L Molarity of EDTA Solution…

Q: Calculate the volume of 0.0602 M EDTA needed to titrate 11.63 mL of 0.0725 M Mg(NO3)2.

Q: Titration of the I2 produced from 0.1142 g of primary-standard KIO3 required 27.95 mL of sodium…

A: Given, Mass of primary standard KIO3 0.1142 g Volume of sodium thiosulfate (Na2S2O3) = 27.95 mL =…

Q: Moles of OCl– in the diluted bleach titrated. ?

A: Iodine and hypochlorite play role in titration Moles of iodine play role in hypochlorite ions

Q: If you have a sample of 42.6 mg/L of calcium and 7.2 mg/L of magnesium, what concentration does the…

A: A numerical problem based on complexometric analysis, which is to be accomplished.

Q: 2. 25.00-mL aliquots of the solution in problem 1 are titrated with EDTA to the calmagite end point.…

A: (A) The volume of EDTA required for blank titration is 2.12 mL. The volume of EDTA required for…

Q: Calculate the volume of 0.0500M EDTA needed to titrate 26.37 mL of 0.0741M Mg(NO3)2 Molar Mass:…

A: Given: Molarity of Mg(NO3)2= 0.0741 M Molarity of EDTA = 0.0500 M The volume of Mg(NO3)2 =26.37 mL…

Q: 3. A 100-mL sample of hard water is titrated with the EDTA solution in problem 2. The same amount of…

A: Solution for Q3 and parts are asked.

Q: 0.5131-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04614 M AgNO3…

A: Mohr titration is a way to quantify Br- and Cl - ions in the solution The reaction is KBr(aq) +…

Q: Considering the graph given, what is the most suitable pH for the titration of calcium with EDTA?

A: pH 10 buffer is used in EDTA titration because in EDTA Y4- is predominant, and we want Y4- to react…

Q: what is the value of magnesium in ppm in the sample?(Mg:24 g/mol)

A: The titration reaction is: Mg2+ + EDTA-4 ====> Mg(EDTA)-2 Let us first calculate moles of EDTA…

Q: Considering the graph given, what is the most suitable pH for the titration of calcium with EDTA?…

A: The determination of the calcium by titration with EDTA is one of the classic methods. The structure…

Q: 1.What the difference between primary and secondary standard substances? 2.Calculate the volume of…

Q: The Ksp of Mg(OH)2 was determined from the following data: 0.0504 L of Mg(OH)2 solution was titrated…

A: Given, Volume of Mg(OH)2 = 0.0504 L Volume of HCl = 0.02474 L Concentration of HCl = 0.534 M

Q: Titration of 50.00 mL of 0.04715 M Na2C2O4 req

A: Given redox reaction is +7 +3 +2…

Q: Determine the molarity of the 10.00 mL standard EDTA solution titrated using 1.000 g zinc sulfate in…

A: 1- First determine the moles of ZnSO4 : Moles = [ mass / molar mass ] Moles = [ 1.000g /…

Q: Calculate pPb of a solution formed by adding 25 mL of 0.1 M EDTA solution to 12.5 mL of 0.2 M Pb2+…

A: Given: Concentration of EDTA = 0.1 M Volume of EDTA solution =25 mL Concentration of Pb2+= 0.2 M…

Q: 11) Will a 0.15 M solution of NH3 be sufficient to keep Zn2+ from precipitating from a solution of…

Q: What is the most appropriate glassware to be used in transferring a 1.000 M Na2CO3 primary standard…

A: Practical physical chemistry:

Q: An EDTA solution is standardized against 0.3982 g of 99.99% CaCO3 (100.09 g/mol) dissolved in HCl…

A: given data mass of CaCO3 is 0.3982g the volume of EDTA Is 38.00Ml pH is 10.0

Q: which of the following is the concentration of the EDTA solution in terms of molarity

A: Solution: Here given experimente is carried out to know concentration of EDTA solution. Where,…

Q: Calculate the volume of 0.0500 M EDTA needed to titrate 29.13 mL of 0.0598 M Mg(NO3 )2. Use a MW…

Q: What is the value of pMg for 50.0 ml of a 0.0500 M Mg2 solution buffered at pH 10.00 and titrated…

A: Magnesium ions react with EDTA to form magnesium EDTA complex. we have to calculate P value of…

Q: At 40.0 mL 0.0050 M Sr2 + pH 10, 0.0100 M EDTA is titrated. Calculate the pSr for the equivalence…

A: Complexometric titration involves analysing the concentration of an unknown solution by titrating it…

Question

A solution contains 1.694 mg of CoSO4 per milliliter. Calculate the
volume of 0.08640M EDTA needed to titrate a 25.00-mL aliquot of this
solution.
Molar Mass: CoSO4 = 155.0

with solution please :))

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

A chemist is given a piece of limestone and told that 50.00% of the sample exists as calcium oxide (CaO). To analyze the sample, the chemist wants to dissolve a portion of the sample in 100 mL and then titrate an aliquot (10 mL) using 0.005300 M EDTA. How much sample (in grams) is needed if a titration volume of 25.00 mL EDTA is desired?
Determine the molar concentration of an EDTA solution of which 26.44 mL were required to titrate a sample containing 287.4 mg of primary standard CaCO3.
A 3.25 g sample of an iron-containing mineral was dissolved in an acid medium and calibrated to 500 mL. A 25.00 mL aliquot was titrated with 0.0025 M KMnO4 spending a volume of 9.32 mL. Subsequently, a 25.00 mL aliquot was passed through a Walden reducer to later titrate it with the same permanganate solution, using a volume of 14.15 mL for the titration. Determine the percentage of Fe(III) in the sample and report it as % Fe2O3
Calculate the volume of 0.0602 M EDTA needed to titrate 11.63 mL of 0.0725 M Mg(NO3)2.
7. A solution contains 1.569 mg/mL of CoSO4(MM = 155.0 g/mol). Calculate the volume of 0.007840 M EDTA needed to titrate a 25.00 mL aliquot of this solution. 8. Calculate the volume of 0.0500 M EDTA needed to titrate 29.13 mL of 0.0598 M Mg(NO3)2.
A 0.1021 g sample containing ZnO was titrated using a standard EDTA solution with Erichrome Black T as an indicator. It took 25.52 mL of 0.0100 M EDTA to reach the endpoint. What is the percentage of ZnO in the sample?
A 49.10 mL aliquot from a 0.500 L solution that contains 0.530 g of MnSO4 (MW=151.00 g/mol) required 41.6 mL of an EDTA solution to reach the end point in a titration. What mass, in milligrams, of CaCO3 ( MW=100.09 g/mol) will react with 1.53 mL of the EDTA solution?
25.00 mL aliquots of the solution in problem 1 are titrated with EDTA to the calmagite end point. A blank containing a small measured amount of Mg^2+ requires 2.12 mL of the EDTA to reach the end point. An aliquot to which the same amount of Mg^2+ is added requires 25.88 mL of the EDTA to reach the end point.
To determine the concentration of an EDTA solution, the following magnesium(II) solution is prepared: metallic magnesium (m(Mg) = 0.5915 g) is dissolved in dilute sulfuric acid, the resulting solution is poured into a volumetric flask with a volume of 0.250 L and is filled to the graduation mark with water. The titration of an aliquot of magnesium(II) solution with a volume of 25.00 ml consumes (11.11 ml; 11.32 ml; 11.24 ml; 11.29 ml) of EDTA. Calculate the concentration of EDTA solution with accuracy corresponding to the starting data, give confidence interval.
At pH 7, what metal ions can be titrated by EDTA?
A sample of impure NaOH, which has been partially converted to Na2CO3 by exposure to CO2, is analyzed by titrating a 188.5 mg sample with 0.1065 M HCl. The volume required to reach phenolphtalein end point is 39.19 ml while the volume required to reach bromocresol green end point is 40.67 ml. Calculate the percentages of NaOH (MWt= 40 g/mole) and Na2CO3 (MWt=83 g/mole) in the sample.
6mL of 125mM EDTA was added to 244mL of water. The resulting solution was added to 219mL of water and the pH was adjusted to 8.0 using 6mL of NaOH. A further 25mL of water was added. What is the concentration of the final solution (in micromolar)? MW of EDTA is 292.24, MW of NaOH is 39.99