Consider a circular cam of eccentricity R/2 as shown in Figure Q1. The cam is pivoted at O and has a diameter of 32 mm. The position coordinate of the follower A is x and the angle is given by: R x(8) : cos e + vcos²0 + 3) V %3D Assume the cam rotates in the clockwise direction with an angular velocity of 2000 rev/min. At an angular displacement of 45° find the velocity of the follower.

Consider a circular cam of eccentricity R/2 as shown in Figure Q1. The cam is pivoted at O and has a diameter of 32 mm. The position coordinate of the follower A is x and the angle is given by: R x(8) : cos e + vcos²0 + 3) V %3D Assume the cam rotates in the clockwise direction with an angular velocity of 2000 rev/min. At an angular displacement of 45° find the velocity of the follower.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q7:-A cam having a lift of 1 cm operates the suction valve of 4-stroke cycle petrol engine. The least radius of the cam is 2 cm and the nose circle radius is 0.25 cm. The crank angle of the engine, when suction valve opens is 4° after T.D.C. and it is 50° after B.D.C. when the suction valve closes. The valve is integral with the camshaft and operates as flat-faced follower. Estimate (a) the maximum velocity of the valve when the engine speed is 2000 rpm, (b) the maximum acceleration and retardation of the valve and (c) the maximum and minimum force to be exerted by the spring to overcome inertia of the valve parts which weigh 2 N.
Q6:- Particulars of a symmetric tangent cam operating a roller follower in a 4-stroke engine are as follows:- (a) basic circle radius=3 cm, (b) roller radius=1.5 cm, (c) angle of ascent=75°, (d) total lift=1.5 cm and (e) the engine speed=1200 rpm. Calculate:- (a) the principal dimensions, (b) maximum velocity and (c) maximum acceleration and deceleration.
I need detail answer do not copy A cam is required for an automated transfer mechanism. The cam follower must rise upward 10 mm with constant velocity in 3.0 sec, dwell for 2 sec, fall with constant velocity in 4 sec, dwell for 1 sec, and then repeat the sequence . a) Determine the required speed of the cam. b) Draw the displacement diagram along with velocity curve. c) The base circle diameter of the cam is 50 mm. Plot the cam profile when a knife-edge follower is incorporated.
Design a cam to raise a valve with simple harmonic motion through 15mm is 1/3rd of a revolution, keep it fully raised through 1/12th of a revolution and to lower it with SHM in 1/6th of a revolution. The valve remains closed during the rest of the revolution. The diameter of the roller is 20mm and the minimum radius of the cam is 25mm. The axis of the valve rod passes through the axis of the cam shaft. If the cam shaft rotates at uniform speed of 100 rpm; find the maximum velocity and acceleration of the valve during raising and lowering. Also draw the profile of the cam.
ONLY NEED PART B QUESTION c A) A follower for a cylindrical cam is required to travel with simple harmonic motion from datum zero to a maximum rise in 100° of cam rotation, dwell for 80° and return with simple harmonic motion to datum zero in the remaining 180° of cam rotation. Assuming your own values for the rise, base circle diameter and slot dimensions, draw a displacement diagram and suggest a layout for the cylindrical cam. B). a). A radial cam with a reciprocating follower is to be driven by a constant-speed motor at 150 rpm. The follower is to start from a dwell, accelerate to a uniform velocity of 25 in/s, maintain this velocity for 1.25 in of rise, decelerate to the top of the lift, return, and then dwell for 0.10 s. The total lift is to be 3.00 in. Determine the complete specifications of the displacement diagram. b). Assuming that the displacement characteristics in part A are to be achieved by a radial cam with a reciprocating flat-face follower, determine the minimum…
A cam have the following specifications: Follower to move outward through 5 cm during 90° of cam rotation, it dwells for the next 60°. The follower then return to its original position through an angle 0R and then dwell for the rest of the cam rotation of 110°. The displacement of the follower is to take place with constant speed motion during both the outward and return strokes. The least radius of the cam is 4 cm. If the cam rotates at 300 r.p.m., construct the displacement, velocity and acceleration diagrams. Also determine The displacement, velocity, acceleration and the pressure angle for the following angles (40°, 75°, 145°, 200°).
Draw the profile of a cam operating a roller reciprocating follower and with the following data: Minimum radius of cam =25 mm; lift=30mm; Roller diameter= 15mm. The cam lifts the follower for 120° with SHM, followed by a dwell period of 30. Then the follower lowers down during 150° of cam rotation with uniform acceleration and retardation followed by a dwell period. If the cam rotates at a uniform speed of 150 RPM. Calculate the maximum velocity and acceleration of follower during the descent period
A cam, with a minimum radius of 25 mm, rotating clockwise at a uniform speed is to be designed to give a roller follower, at the end of a valve rod, motion described below : 1. To raise the valve through 50 mm during 120° rotation of the cam ; 2. To keep the valve fully raised through next 30°; 3. To lower the valve during next 120°; and 4. To keep the valve closed during rest of the revolution i.e. 90° ; The diameter of the roller is 20 mm and the diameter of the cam shaft is 25 mm. Draw the profile of the cam when (a) the line of stroke of the valve rod passes through the axis of the cam shaft, and (b) the line of the stroke is offset 15 mm from the axis of the cam shaft. The displacement of the valve, while being raised and lowered, is to take place with simple harmonic motion. Determine the maximum acceleration of the valve rod when the cam shaft rotates at 100 r.p.m. Draw the displacement, the velocity and the acceleration diagrams for one complete revolution of the cam.
A disc cam rotating in a clockwise direction is used to move a reciprocating roller with simple harmonic motion in a radial path, as given below: (1) Outstroke with maximum displacement of 25 mm during 120° of cam rotation, (ii) Dwell for 60° of cam rotation, (iii) Return stroke with maximum displacement of 25 mm during 90° of cam rotation, and (iv) Dwell during remaining 90° of cam rotation. The line of reciprocation of follower passes through the camshaft axis. The maximum radius of cam is 20 mm. If the roller diameter is 8 mm. Draw the profile of the cam when the line of reciprocation of the follower is offset by 20 mm towards right from the cam shaft axis.
Draw a Cam with uniform motion of follower based on the following data. 45 mm minimum diameter of Cam, 50 mm lift (rise) with uniform velocity, 0º to 90º Rise, 90º to 180º Top dwell, 180º to 270º Fall, 270º to 360º bottom dwell, clockwise rotation. The diameter of Cam Shaft hole is 25mm.
A cam is required for an automated transfer mechanism. The cam follower must rise upward 10 mm with constant velocity in 3.0 sec, dwell for 2 sec, fall with constant velocity in 4 sec, dwell for 1 sec, and then repeat the sequence . a) Determine the required speed of the cam. b) Draw the displacement diagram along with velocity curve. c) The base circle diameter of the cam is 50 mm. Plot the cam profile when a knife-edge follower is incorporated.
A follower for a cylindrical cam is required to travel with simple harmonic motion from datum zero to a maximum rise in 100° of cam rotation, dwell for 80° and return with simple harmonic motion to datum zero in the remaining 180° of cam rotation. Assuming your own values for the rise, base circle diameter and slot dimensions, draw a displacement diagram and suggest a layout for the cylindrical cam.