Consider a cylindrical tank (diameter = 8 m and depth = 5 m) that contains water at 15ºC and is filled up to the brim. If the water is heated to 60ºC, calculate the amount of water that will spill over the edge of the tank. Assume the tank does not expand with the change in temperature. You may use the table given in the Appendix section for reference.

Consider a cylindrical tank (diameter = 8 m and depth = 5 m) that contains water at 15ºC and is filled up to the brim. If the water is heated to 60ºC, calculate the amount of water that will spill over the edge of the tank. Assume the tank does not expand with the change in temperature. You may use the table given in the Appendix section for reference.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 23P

See similar textbooks

Similar questions

For water, starting with 1 m3 of water in a container, what is the pressure required to decrease the volume of water by 1%?
1.) Calculate the volume of a water cylinder with a total height of 10 meters and whose diameter is 400 centimeters, whose top section is a semi-sphere? 2.) calculate the volume of a cylinder where: a.) the area of the base is 30cm^2 and the height is 6cm. b.) the radius of the base is 14cm and the height is 10cm.
There are two identical 316 stainless steel tanks that are 2.5 m long and have an inside diameter of 60 cm . One of the tanks is filled with air and the other tank is filled with water at 20 ° C . Complete the following table using the given density for air and water
The outside diameter of a right circular cylindrical tank is 3,000 mm and its height is 6,000 mm. If the thickness of the tank is ¼ inch, calculate the capacity in gallons.
Figure 1 shows a tank containing water. One side of the tank is open to the atmosphere and theother side is sealed with air above the water.a. Calculate the pressures (gage) at Points A, B, C, D, E and F.b. What is the air pressure in the right side of the tank?
Show complete solutions and figures. The shown tank with an attached manometer contains water unit weight is 9.79 kN/cu.m.at 200oC. The atmospheric pressure is 100kPa. There is a valve located 1m from the surface of the water in the manometer. The valve is closed trapping the air in the manometer, and the water is added to the tank to the level of the valve. Find the increase in the elevation of the water in the manometer assuming the air in the manometer is compressed isothermally. a) 101.3mm b) 92.7mm c) 73.2mm d) 82.4mm e) None
Figure 7 shows a pump partially submerged in oil (sg=0.90) and supported by springs. If the total weight of the pump is 14.6 lb and the submerged volume is 40 in3 , calculate the supporting force exerted by the springs.
Please show the complete solution. (Example: Conversion of Units) A rigid container is closed at one end and measures 8 in diameter by 12 in long. The container is held vertical and is slowly moved downward until the pressure in the container is 17 psia. What will be the depth of the top of the container from the free water surface?
Assuming sea water to be incompressible, what is the pressure in tons per square foot 2miles below the surface of the ocean? Take the unit weight of sea water to be 64 lb/ft 3 .a. Write the given and required.b. Illustration of the problemc. Solution
A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of the diameter of 0.4 m at the bottom. Find the time taken by water to fall from 4 m to 2m. Take Cd= 0.60. Include a diagram in your solution. a.24.8 seconds b.47.8 seconds c.43.8 seconds d.84.7 seconds
A pressure in a given tank reads 381 mm of Hg. Determine the equivalent height of a certain fluid in m with sp.gr= 3.35. Round your answer to 2 decimal places.
1. You need a cylinder that can contain an amount of liquid. Measure themaximum amount of water that your cylinder can contain in cm 3 and ml.2. Measure the dimensions of your cylinder (h and d) in cm.3. Solve for the volume of your cylinder.4. Record all results in the table provided. Table 1. Dimensions and capacity of the cylinder Capacity in cm 3 Capacity in ml Circumference Diameter Volume