Answered: Convert a flow of water flowing in a…

Engineering

Civil Engineering

Convert a flow of water flowing in a pipe 410 Liters/ hr into kg/hr, m³/min discharge in kg/hr discharge in m3/min

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter13: Energy And Power

Section: Chapter Questions

Problem 5P

See similar textbooks

Related questions

Q: Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: Three pipes of different lengths and diameters are connected in series as shown. All pipes have f =…

Q: A tank is shaped like a vertical cylinder; it initially contains water to a depth of 9 ft, and a…

Q: An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter…

A: Let's suppose, the suction side as point A and the discharge side as point B, and the vertical…

Q: Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above…

A: a) The expression for energy between velocity 1 and 2 is given as P1γ+V122g+z1+HP=P2γ+V222g+z2…

Q: In Figure 6 is shown a siphon discharging water from reservoir A into the air at B. Distance 'a' is…

Q: A cylindrical tank 400 mm in diameter, discharges water through a 30 mm diamater orifice under a…

A: Given, Diameter of the cylindrical tank, D= 400mm Diameter of the orifice, d= 30mm Constant head, H=…

Q: Subject: Fluid Mechanics/Hydraulics 1.) What is the specific weight of air in N/m3 at 442 kPa…

Q: A nozzle of inner radius 1.06 mm is connected to a hose of inner radius 9.05 mm. The nozzle shoots…

Q: The following figure shows a pump that extracts water from a reservoir with a volumetric discharge…

Q: Q) Calculate velocity and flow rate of fluid (Water) in pipes. Also, determine the power of the…

Q: Water flows from the rectangular outlet as shown in the figure. Estimate the flow rate per unit…

A: Given that, H = 2 m, h=80 cm, the flow rate per unit width has to be determined.

Q: SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in…

Q: What volume flow rate in gallons per minute of oil (sg3D0.90) is in the system ? 75-mm inside…

Q: Calculate the discharge in liters per second through a 150 mm diameter orifice having a head of 3.2…

A: Diameter of orifce, D=150mm=0.15mThe head , H=3.2mThe coefficient of contraction, Cc=0.63The…

Q: A 150 mm diameter pipe 60 m long connects two reservoirs. Determine the difference in elevation…

A: To Determine The difference in elevation between the water surfaces of the two reservoirs, hL

Q: A cylindrical tank 400 mm in diameter, discharges water through a 30 mm orifice under a constant…

Q: A liquid flow through pipe of diameter 10 cm a velocity of 6 cm Find the value of discharge

Q: A 9.2-kg plastic tank that has a volume of 3.3 m3 is filled with liquid water. Assuming the density…

Q: 4. A Venturi meter is installed in a pipeline carrying air. The meter has a diameter of 600 mm at…

A: It is highly accurate discharge measuring instrument of incomprehensible fluid flow. It consists of…

Q: Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: Water in a reservoir is flowing through a hydroelectric plant. The water level in the reservoir is…

A: Asked: To determine the head available to drive the turbine. Given: Head of water in the…

Q: A fixed control volume has three one-dimensional boundary sections, as shown. The flow within the…

A: Rate of change of the energy of the system which occupies the (er) at this instant Where,…

Q: An 85-percent-efficient pump is used to increase the pressure of water in a 10-cm-diameter pipe from…

A: Given data, Efficiency of pump = 0.85 Diameter of pipe = 10 cm P1 = 120 kPa P2 = 800 kPa To find…

Q: Topics: Fundamental of fluid flow In Lake Geneva (Switzerland), there is a water jet (called the…

A: step 1-

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

A: Given: Volume of water in rigid container, V = 1 m3 Pressure applied by the piston = 46 Mpa = 46 *…

Q: A rectangular tank 4 m long, 1.5 m wide contains water up to a height of 2 m. Calculate the depth of…

A: Given data in question Width Depth Height To find out Depth of cemter of pressure

Q: PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d'Eau) that is…

A: Bernoulli equation ; By neglecting all losses ; P1ρg + V122g+h1 = P2ρg + V222g+h2 From above figure…

Q: Q3. A pump is required to pump water from a large reservoir to the water tower located 20 m above…

A: Given : z1 = 0 z2 = 20 P1 = 0 P2 = 0 hL = 0 D = 30 mm Q = 0.03 m3/s ρ=1000 kg/m3 V1 = 0 A)…

Q: b) The small turbine shown below extracts 400 W of power from the water flow. Both pipes are wrought…

A: Schematic diagram of the given problem:

Q: PROBLEM 10: A circular orifice is located 5m. below the water surface. If the tank is large and the…

Q: length of 10 m, friction coefficient of 0.025, and local coefficient of 2; discharge pipe has:…

A: Given:- distance between water levels in the two tanks is 25 m; pump capacity is 10 m3/h; suction…

Q: PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d'Eau) that is…

A: Velocity is v=2ghv=2×9.81×130v=50.503ms

Q: Water flows from the nozzle shown in figure. Determine the flowrate and the .height (h) to which the…

Q: The flow of water in a pipe of about 3 meters in diameter can be measured by a. venturimeter b.…

A: Venturimeter:- Venturimetre is a device used for measuring the rate of flow of fluid flowing through…

Q: An open tank has a vertical partition and on one side contains gasoline with a density p= 800 kg/m³…

A: Solution

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A: Calculate entry loss and friction loss for the first pipe:

Q: Three pipes are connected in parallel. The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: A pump takes water from an 8 inch suction pipe and delivers it to a 6 inch pipe in which the…

Q: The discharge through a 75mm diameter orifice at the bottom of a large tank was measured to be 1734…

A: Hello dear this is the solution of your problem The answer is found to be Coefficient of…

Q: Given: diameter of orifice=100mm diameter of tank=1.2m C=0.65 solve for the time it takes to:…

A: We have to determine time it takes to: a) remove the first liquid b) remove the second liquid c)…

Q: Water is flowing from the tank into a series of pipes and then into the atmosphere through 75…

Q: 75-mm inside diameter Flow 0.25 m 200- inside 0.60 m diameter Water

Q: Calculate the hydraulic power of a pump (kW) that transfers water at 300 m3/hr to a tank at an…

A: Given values for the numerical are: Discharge of the pump, q= 300 m3/hr Elevation of the tank= 11m…

Q: The tank shown has one curved surface restraining a body of static fluid, with the following…

A: To find the magnitude of resultant force subtract the subtract the magnitude of the smaller force…

Q: Calculate the diameter of the nozzle (in mm) by a jet of water discharging freely out of a nozzle,…

A: Answer : b.25.4

Q: Oil with a specific weight of 8.64 kN/m3 flows from A to B through the special fabricated system…

A: Given:- specific weight=8.64kN/m3 Sgo=1.4 To find:- volume flow rate of oil

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Convert a flow of water flowing in a pipe 410
Liters/ hr into
kg/hr,
_m³/min
discharge in kg/hr
discharge in m3/min

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the rate of flow of water through a pipe of diameter 10 cm and length 60 cm when one end of the pipe is connected to a tank and other end of the pipe is open to the atmosphere. The height of water in the tank from the centre of the pipe is 5 cm. Pipe is given as horizontal and value of f= 0.01. Consider minor losses.
A horizontal pipe carries cooling water from a reservoir as shown in the following figure. If the pipe diameter is 20 cm, the flow rate is 0.06 m3/s, what is the pressure at L= 2000 m? Calculate head loss as hL = 0.015(L/D)(V 2/2g)
In the figure shown below, it is desired to pump 5259705 lit/day of water from a stream to a pool. El. A = 49m while El. B = 98 m. If the combined pump and motor efficiency is 90%, calculate the monthly power cost in pesos if electricity rate is P10 per kW-hr. Assume that the pump operates for 24 hours and take 1 month = 31 days; Round your answer to 4 decimal places. Pipe Length (m) Diameter (mm) Hazen Coefficient 1 1997 m 375 mm 120 2 1514 m 240 mm 122 3 902 m 205 mm 149
An open cylindrical tank 800mm in diameter and 2000mm high contains water to a depth of 1.6m. It is rotated about its vertical axis at 13 rad/s. How many liters of water are spilled? Use density of water as 1000kg/m3 and specific weight as 9.81kN/m3
The venture meter shown carries oil (sg=0.80). Calculate the volume flow rate of the system
With velocity of 9 m/s in the 234 mm diameter pipe in the figure shown, determine the discharge in pipe 4 in m3/s. Assume f = 0.063 for all pipes and neglect minor losses. The following are the properties of each pipe: Pipe 1 (Length=467 m, Diameter = 234 mm) Pipe 2 (Length=598 m, Diameter = 385 mm) Pipe 3 (Length=307 m, Diameter = 732 mm) Pipe 4 (Length=823 m, Diameter = 312 mm) Pipe 5 (Length=1191 m, Diameter = 512 mm)
Instead of a 0.9 cm diameter water pipe, a 2.3 cm diameter pipe was installed. 8.6 liters of water per second was obtained from the previous water pipe. How fast does the water come out of the new line in liters per second? Other aspects related to water pipes are assumed to remain unchanged.
With velocity of 7 m/s in the 330 mm diameter pipe in the figure shown, determine the discharge in pipe 3 in m3/s. Assume f = 0.046 for all pipes and neglect minor losses. The following are the properties of each pipe: Pipe 1 (Length=572 m, Diameter = 330 mm) Pipe 2 (Length=344 m, Diameter = 536 mm) Pipe 3 (Length=391 m, Diameter = 963 mm) Pipe 4 (Length=867 m, Diameter = 317 mm) Pipe 5 (Length=991 m, Diameter = 310 mm) Round your answers in 3 decimal places.
Determine the flow of water in cubic centimeters. Asap 10 mins
From point A to point B of the system shown in the figure, oil flows (specific gravity of 8.64 kN/m3). A) Calculate the volumetric flow of the oil. ( WORK LIKE NEW PLEASE)
The flow into a reservoir over a one hour period is shown in the following table. tt (minutes) 0 10 20 30 40 50 60 dVdtdVdt (gallons/minute) 258 332 370 447 436 435 320 Estimate the total volume entering the reservoir in 60 minute using the flow rate at the beginning of each interval. gallonsEstimate the total volume entering the reservoir in 60 minute using the flow rate at the end of each interval. gallons
Hydraulics 6. Determine the Reynolds number of a 0.40 cubic meter per second oil of Gs=0.80 and an absolute viscosity of 0.025 Pa.s thru a 450 mm diameter pipe.