Consider the below sequential circuit to determine the values of L M, N, Q in the corresponding state diagram of the circuit. Note: if needed, save the picture to your PC and zoom to see better Note: in states, A is the most significant and B is the least significant

Consider the below sequential circuit to determine the values of L M, N, Q in the corresponding state diagram of the circuit. Note: if needed, save the picture to your PC and zoom to see better Note: in states, A is the most significant and B is the least significant

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Create a logic circuit using only basic gates such as AND, OR, NOR, NAND, NOT, etc. to implement a Subtractor that is capable of subtracting the second number from the first, by converting the second number into its 2's complement form and then adding the resulting number to the first number. You do not need to worry about accomodating the addition or subtraction of negative numbers. Also, create a limited ALU (Arithmetic logic unit) circuit using Logism that implements a Full Adder circuit capable of adding 2 – 4 bit binary numbers and subtracting 2- 4 bit binary numbers. Also, implement the ability to select a bitwise AND operation and a bitwise OR operation. For the ALU it is acceptable to use the Adder and Subtractor circuits that are listed under the "Arithmetic" folder in Logism. (Logism tips and tricks are useful here for multi-bit pins, and how to set up different gates to support more than 1 bit. If using YOUR adder or subtractor circuit in your ALU that is not only acceptable…
What is the following situation? In some situations particular input sequences will never occur as inputs to a sequential circuit. In other cases, the output from a sequential circuit is only observed at certain times rather than at every clock time. These situations lead to unspecified next states or outputs in the state table. a. An incompletely specified state table. b. An imperfect state table. c. A partial state table. d. A gapped state table.
Question 1 : See the attached picture a.Write a logical function for the following circuit and then construct a truth table ? b.Implement the circuit using only the minimum possible IC SN74LS00 ? c. Check that your table matches the output of the circuit you created ? d. Also make the original circuit as above and then compare the results with the circuit you made using IC SN74LS00. The output should be the same ? Question 2 : Know the functions as below:F = AB + A'( B' + C ) a. Create a truth table for the function ? b.Implement the circuit using IC SN74LS00 to a minimum ? c.Customize your table with the output in the circuit you created ?
Implement a combinational circuit with three inputs x, y, and z and three outputs A, B, and C.When the binary input is equal to 0, 1, 2 or 3, then the output is equal to the input + 1.When the binary input is 4, 5, 6 or 7 then the binary output is equal to the input – 2.
Use muxes to implement various gates. In each circuit, draw the specified number of 2:1 muxes and implement the given boolean expression. A mux input can be A, B, 0, 1, or the output of another device (e.g., another mux or a decoder). Be sure to label the S, 0, and 1 inputs of every mux. a. Use one 2:1 mux to implement NOT A (i.e. A') b. Use one 2:1 mux to implement A AND B (i.e. AB) c. Use one 2:1 mux to implement A OR B (i.e. A+B)
A combinational circuit with four inputs (A,B,C,D) and one output (Z) is designed as follows using an 8:1 multiplexer. Inputs A,B,C are connected to the select lines ?S2, S1, S0 respectively. Multiplexer has the following values connected to the data inputs: I0,I6 =1; I1,I3 =D; I2,I5 =0; I4,I7 =D’ Write the simplest logic expression of the circuit realized above Z= f(A, B, C, D)
Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
Using Verilog continuous assignments or VHDL signal assignments, write a description of the circuit specified by the following Boolean functions: Out_1=(A+B′)C′(C+D)Out_2=(C′D+BCD+CD′)(A′+B)Out_2= (AB+C)D+B′CWrite a testbench and simulate the circuit’s behavior.
Using the truth table below ( An example sum-of-products expression is (A+B+C)(A+B+C')(A+B'+C)(A'+B+C).) a. Write a product-of-sums Boolean expression bexp4 for the output ? of the truth table b. Draw a circuit that is a direct translation of bexp4 without any simplification. For the circuit, use a layout that is analogous to the layout of the sample circuit below (where the and and or gates are appropriately swapped).
Design a circuit to implement the following truth table, where A and B are inputs and Z is the output. Give the Boolean equation that implements the circuit in the space provided. There may be more than one possible correct answer. You only need to list one possible correct answer. Input Output A B Z 0 0 1 0 1 0 1 0 1 1 1 1
Assume we are writing a testbench for a sequential circuit that has three control inputs (cA, cB, cC) and a periodic clock (clk). If we define CLK_PERIOD as a localparameter with a value of 50 (nsec), write the testbench segment that would ensure all possible combinations of the control inputs were tested on a clock rising edge. This is can be done more elegantly if you define each time step in terms of the constant CLK_PERIOD. Your answer should include the statements that define clk, cA, cB, and cC over time. Hint: think of how you would show all combinations of three variables on a truth table and replicate that over time, where each combination is held over a timespan with a clock triggering edge.
1a. Draw a circuit diagram using appropriate logic gates to implement a 3-bit comparator. Identifythe gates used in implementation and show its usage to compare two 3-bit words by writing thetruth table. b. Write the Boolean expression for the following 4 input circuit. Include sub-expressions foroutputs of each gate. c. Complete a truth table for the previous logic gate circuit in part b. d. Write the Boolean expression for the new circuit below. Then, simplify the following logic circuitusing the theorems in Boolean algebra. Show the steps clearly and specify the law used in eachstep. Finally draw the simplified circuit diagram.