Consider the following three phase balanced circuit. 21020° Vrms j0.5 N 24– j21 N 2102-120° Vrms j0.5 2 (-+) | 24– j21 2 ell | 24– j21 N 210/120° Vrms j0.5 2 Find average power dissipated by the delta connected load. (a) 8587.18 W (b) -8587.18 w (c) 7514.41 W (d) -7514.41 W

Consider the following three phase balanced circuit. 21020° Vrms j0.5 N 24– j21 N 2102-120° Vrms j0.5 2 (-+) | 24– j21 2 ell | 24– j21 N 210/120° Vrms j0.5 2 Find average power dissipated by the delta connected load. (a) 8587.18 W (b) -8587.18 w (c) 7514.41 W (d) -7514.41 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21MCQ: The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts....

See similar textbooks

Related questions

Q: magnitude of the complex power supplied by a 3-phase balanced Y-Y system is 4800 VA. The line…

A: First we will find out the phase current from given data then we will calculate impedance from phase…

Q: Consider the following three phase balanced circuit. 21020° Vrms j0.5 2 -+ 24-j21 N 2102-120° Vrms…

Q: For the circuit shown below, all the voltage values are given in rms. The apparent power of the…

A: The given circuit is: All voltages values are given in RMS. Apparent power of three phase load,…

Q: A 60 Hz, 230 mile, three-phase overhead transmission line has a series impedance of o.8431…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a…

Q: A three-phase circuit has two parallel connected balanced loads. The first is a balanced delta load…

A: The solution is given below

Q: )A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected…

A: The solution can be achieved as follows.

Q: A three-phase unbalanced source with the following phase-to-neutral voltages 2. 200 /25° 100 L-155°…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 12. In an unbalanced system, the phase voltages are: Vna = 13220 Vnb = 1302235 Vnc = 1332117 What is…

A: 12. Given parameters are: Vna=132∠0°V,Vnb=130∠235°V,Vna=133∠117°V, The line to line voltage is:…

Q: Q4) The three phase circuit seen in the following figure is derived by a three phase balanced…

A: the sinusoidal steady-state solution of the iR (t) current , and . the total complex power consumed…

Q: An unbalanced star-connected load is supplied from a 400-V, 3-ph, Y-connected alternator through…

Q: (b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta-…

Q: A three-phase circuit has two parallel connected balanced loads. The first balanced delta load with…

A: The solution is given below

Q: Star connected source with 3-phase balanced positive phase sequence feeds the delta connected…

A: Note: As per Bartleby Portal, I am solving first three sub parts.

Q: DIagram: FauLt h phase 3phase Load Source 2 Line Values: sourte Line Impedances: • Eon: 120 L0' v •)…

A: Under unbalanced condition with fault We have to find load power profile Active (PT), reactive (QT),…

Q: 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source.…

Q: Q5. The one-line diagram of a three-phase power system is shown in Figure 1. Select a common base of…

A: For a three phase power system, the one-line diagram is shown below, Common base on the generator…

Q: Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a…

Q: Problem 1. A balanced delta connected load of 15 +j18 2 per phase is connected at the end of a…

A: In the question, 3 phase balance supplied to 3 phase balance delta load Find the line current,…

Q: Q. NO.2 In a balanced A-connected three phase load, applied with three phase supply 100X V rms…

Q: = 200/0° A balanced Y-connected generator with terminal voltage Vn volts is connected to a…

A: Sequence component: There are three sequence components in the power system, positive sequence,…

Q: Q1 (a) A 3 phase industrial load can be represented by a balanced star connected load (ZRN etc) of…

Q: Single line diagram of a three-phase power system is shown in the Figure Q1. Draw out the per phase…

Q: are connected in mesh across a three-phase 435V ac supply. Determine the phase current, line…

Q: 2. In an unbalanced system, the phase voltages are: Vna = 13240 What is the line to line voltage…

A: In this question, Unbalanced voltages are given. Find the line voltage VCB ? VCB = Vnb -Vnc

Q: lanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with ab-bc-ca…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltagesVLL =…

Q: Two parallel three-phase loads are connected to a three-phase a connected source through a line. The…

A: The delta connected source supplies the two parallel-connected loads in which one load is in star…

Q: In a balanced Y-Y circuit shown in Figure 5, the magnitude of the phase voltage at the source is Vp…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

A: The load shown below is connected to a 360 V, 50 Hz three-phase supply with a positive phase…

Q: Three balanced 3 phase loads are connected in parallel. Load 1 is Y–connected with an impedance of…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: A single phase distībutor AB has a total impedance of (0-1+j0-2) ohm. At the far end B, a curent of…

Q: A Q.20: For the circuit shown, let Z,=Z2=Z3=60Z30°Q are phase impedances, and the phase voltage be a…

Q: A balanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltages =208…

Q: In a balanced abc sequential, three-phase star-star connected system, the total power on the line is…

A: Given

Q: Consider the following three phase balanced circuit. 21020° Vrms j0.5 2 | 24– j21 N 2102-120° Vrms…

A: Given: The given figure is,

Q: Q1) For the circuit shown below, Vab = 240415°, Zy = (12 + j15) 2, the phase sequence is positive.…

A: given data Vab=240∠15 Zy=12+j15

Q: 3- The single phase loads in the circuit can be described as follows: Load 1 absorbs an average…

Q: Q1. A balanced three-phase Y-connected generator with positive sequence has an impedance of 0.4 +…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: In the figure, each transmission line of the three-phase system has an impedance of 0.05 + j0.2 Q.…

A: In this question, We need to determine the current in the loads and neutral, also find the average…

Q: What do you understand by means of power system? A 3-q, 50 Hz transmission [ line is 120 km long. It…

Q: Three balanced 3 phase loads are connected in parallel. Load 1 is Y-connected with an impedance of…

Q: Consider a single-phase load with an applied voltage v(t)=150cos(wt+10°)V and load current…

A: Rewrite the given cosine wave equations of current and voltage in phasor form as fallows

Q: b) A balanced 3 phase Y connected generator with negative sequence has an impedance of 0.3+j0.5 Q/D…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: For the circuit shown, given that Vab=208Z°, abc sequence, ZLine%3D0.1+j0.2 Q and ZLoad= 12+j4 Q.…

A: Magnitude of voltage VAB across load? 3 phase power system

Q: A balanced three-phase with phase voltage of 4200-Vrms and the transmission line has an impedance of…

A: In this question we need to find a loss in transmission line for the given load condition

Q: An unbalanced star-connected load is supplied from a 400-V, 3-ph, Y-connected alternator through…

Q: The voltage across the parallel loads is VI = 24020° V(rms), with the loads: Load 1 absorbs 12 kVA…

A: According to question: The complex power of load 1 is calculated as…

Q: An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance…

A: Given ZL=11.5+j10 ΩZC=8-j20 Ω circuit diagram is

Q: An unbalanced 4 wire star connected load consisting of the phase impedances Zes (15-j5)2. Zs…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Consider the following three phase balanced circuit.
21020° Vrms
j0.5 N
24– j21 N
2102-120° Vrms
j0.5 2
(-+)
| 24– j21 2
ell
| 24– j21 N
210/120° Vrms
j0.5 2
Find average power dissipated by the delta connected load.
(a) 8587.18 W
(b) -8587.18 w
(c) 7514.41 W
(d) -7514.41 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
A three-phase, 3-wires CBA System alternator, sending 3-phase voltages of 339.4 volt to the lines, having a delta connected load, with VCA is the reference vector. ZBC = 12.99 – j7.5 ZCA = 8.66 + j5 ZAB = 10 + j0 Determine the phase and line current b) draw the phasor diagram and c) true power generates by the generator neglect the line losses.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
The one-line diagram of a three-phase power system is as shown in the figure attached. Impedances are marked in per unit on a 100-MVA, 400-kv base. The load at bus 2 is S(sub 2) = 15.93 MW - j33.4 Mvar, and bus 3 is S(sub 3) = 77MW + j14 Mvar. I tis required to hold the voltage at bus 3 at 400 angle 0 degrees kV. Working in per unit, determine the voltage at buses 2 and 1.
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.