Consider the system in the figure below, which is pivoted at point O. Assume that a = 0.4 m, b = 1 m, M = 10 kg, mass of the rigid bar m = 8 kg, k = 3000 N/m and c = 30 N.s/m. Determine the damped natural frequency of the system in Hz. Take g = 9.81 m/s². The moment of inertia of the bar about the pivot point O is I = m² Note: Assume the mass of the rigid bar is uniformly distrusted. This means the centre of gravity of the rigid bar is located at distant from the pivot point O. //////// umm 70 b 1.33 Hz 0.95 Hz 1.22 Hz 1.09 Hz 0.77 Hz a 0 k wwwww Rigid bar

Consider the system in the figure below, which is pivoted at point O. Assume that a = 0.4 m, b = 1 m, M = 10 kg, mass of the rigid bar m = 8 kg, k = 3000 N/m and c = 30 N.s/m. Determine the damped natural frequency of the system in Hz. Take g = 9.81 m/s². The moment of inertia of the bar about the pivot point O is I = m² Note: Assume the mass of the rigid bar is uniformly distrusted. This means the centre of gravity of the rigid bar is located at distant from the pivot point O. //////// umm 70 b 1.33 Hz 0.95 Hz 1.22 Hz 1.09 Hz 0.77 Hz a 0 k wwwww Rigid bar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform rigid mass of 2 lb is hinged at its centre and laterally supported at one end by a spring of constant k=300 N/m. If the equation obtained for frequency (ωn) in this system is ωn2 =k/m, what is the natural frequency?
A mass m is attached to two identical springs having constant k as shown in the figure. What is the natural frequency ∞ of this single degree of freedom system?
Two masses of weight 300 N each are keyed to the opposite ends of a shaft. The shaft length is 70 cm. The shaft is 7 cm diameter for the first 30 cm of its length, 13 cm diameter for the next 20 cm, and 10 cm diameter for the remaining of its length. Find the frequency of free torsional vibrations of the system and the position of the node. The radius of gyration of the masses is 30 cm.
Derive the expression for motion and determine the natural frequency of the system shown in the figure below. Neglect the mass of the rod.
A uniform plank of mass 2.29kg and length 39.6 cm is pivoted at one end, and the opposite end is attached to a spring of force constant 454N/m. The height of the pivot has been adjusted so that the plank will be in equilibrium when it is horizontally oriented as in the figure. Find the period of small oscillation about the equilibrium point. Answer in units of s.
Find the natural frequency (in Hertz) of the system illustrated in the following figure. Assume the disk is slipping without rolling. K1=3,503 N/m, K2=7,496 N/m, M=0.3 kg, and R=0.7 m.
The motor-pump system shown in Fig. 5.36(a) is modeled as a rigid bar of mass m=50kg and mass moment of inertia J0 = 100 kg-m2. The foundation of the system can be replaced by two springs of stiffness k1 = 500 N/m k2 = 200 N/m. and Determine the natural frequencies of the system.
A rigid and weightless rod is restricted to oscillations in the vertical plane as shown in the figure below.Determine the natural frequency of the system of mass m.
Consider a spring-mass system with mass equal to 1 kg, spring constant equal to 25 Newton/meter.Which damping constant b causes critical damping?If the damping constant b in the above system is set to 3 N ∙ sec/m, then what can be said about the number of timesdoes the object pass through its equilibrium position?If the damping constant b in the above system is set to 8 N ∙ sec/m, then what is the interval of time between thesecond time the object returns to its equilibrium position and the third time it returns to its equilibrium position?
Consider the spring mass system shown in Figure Task 2b. It has a mass, m of 4 kg and the spring constants k1 = 5 N/m and k2 = 8 N/m. Determine the natural frequency of vibration of spring mass system inclined at an angle of 30⁰.
Identify the expression for the natural frequency of the system shown in the figure.
An electric motor with a mass of 20 kg is placed in the middle of a beam that is jointly connected on both sides. Rotor its unbalance is equivalent to a mass of 0.3 kg at a distance of 0.020 m from the axis of rotation. Due to the electric motor force acting on the beam t Sin F F  0 . The rotor is rotating at an angular speed of  = 40 rad / sec. Engine under the influence of force Find the displacement amplitude at the point where it is located (in the middle). The beam mass will be neglected. The beam has a modulus of elasticity E = 200000000000 N / m2 (200 GPa).