Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress T= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09

Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates. The applied load in the lap joint is 50 KN and the pitch is 60 mm. If the allowable stresses for the plate material are (tensile stress ot= 120 MPa, shear stress T= 90 MPa, bearing stress oc = 150 MPa) and for the rivet material are (tensile stress ot=130 MPa, shear stress t= 100 MPa, bearing stress oc = 140 MPa) e 8:09

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.16P: Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting...

See similar textbooks

Similar questions

A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a pressure of 2200 psi. The tank is constructed of two hemispheres joined by a welded seam (see figure). (a) What is the tensile load/ (lb per in. of length of weld) carried by the weld? (b) What is the maximum shear stress rm2Xin the wall of the tank? (c) What is the maximum normal strain e in the wall? (For steel, assume E = 30 X 10 psi and v = 0.29.)
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A brass sleeve S is fitted over a steel bolt B (see figure), and the nut is lightened until it is just snug. The bolt has a diameter dB= 25 mm, and the sleeve has inside and outside diameters d1= 26 mm and d2= 36 mm. respectively. Calculate the temperature rise .?T that is required to produce a. compressive stress of 25 MPa in the sleeve. (Use material properties as follows: for the sleeve, as= 21 × 10-6 /? and Es= 100 GPa; for the boll, aB= 10 × 10-6 /? and EB= 200Pa
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the ends. The bar is then subjected to a temperature increase ?T = 25°C. Calculate the complete stale of stress acting on an inclined section .rs that is cut through the bar at an angle ?? = 45*. Use E = 200 GPa and the coefficient of thermal expansion a = 12×10-6/?.