Example 9.3. A double riveted double cover butt joint in plates 20 mm thick is made with 25 mm diameter rivets at 100 mm pitch. The permissible stresses are: o, = 120 MPa; %3D T= 100 MPa; 0= 150 MPa %3D Find the efficiency of joint, taking the strength of the rivet in double shear as twice than that of single shear.

Example 9.3. A double riveted double cover butt joint in plates 20 mm thick is made with 25 mm diameter rivets at 100 mm pitch. The permissible stresses are: o, = 120 MPa; %3D T= 100 MPa; 0= 150 MPa %3D Find the efficiency of joint, taking the strength of the rivet in double shear as twice than that of single shear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the efficiency of the double riveted double cover butt joint having plate thickness 20mm with rivets having a pitch of 100mm. Permissible tensile stress is 120MPa, permissible shear stress is 90MPa and permissible crushing stress is 180MPa.
Fig. 2, shows a cylindrical rod of 25 mm diameter, welded to a flat plate. The cylindrical fillet weld is loaded eccentrically, by a force of 20 kN acting at 200 mm from the welded end. If the size of the weld is 20 mm, determine the shear stress and bending moment.
(D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates under single shear action. If the rivets are made from Aluminium (E=80 GPa) and the plates under tension of 15 kN. Solve this problem to show weather this joint is safe or not. Suppose all the rivets have equal load share.
Calculate the average shear stress in a thin-walled tube having a circular cross section of mean radius ?? and thickness ?, which is subjected to a torque T
The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of 2, calculate the safe shearing resistance of a unit strip of a single-riveted lap joint in which the plate thickness of ¼ in, the pitch joint of ¾ in, and the diameter of the rivet hole is 11/16 inch.
A 5-mm thick plate of steel is formed into the cross section shown in Fig. P8.13. Locate the shear center for the cross section.
A flanged bolt coupling consists of 20-mm aluminum bolts evenly spaced around a bolt circle 30 cm diameter and 12-mm steel bolts on a concentric bolt circle 20 cm in diameter. The allowable shearing stresses are 42 MPa in the aluminum and 62 MPa in the steel. What should be the minimum number of aluminum bolts if there are four steel bolts and the power applied is 760 kW at 600 rpm? Use Gal = 28 GPa and Gst = 83 GPa.
Calculate the average shear stress in a thin-walled tube having a circular cross section of mean radius rm and thickness t, which is subjected to a torque T
Steel railroad reels 15 m long are laid with at an initial temperature Ti = 46 °C. Assume α = 11.7 μm/(m·°C) and E = 200 GPa. What stress would be induced in the rails in MPa at a final temperature of Tf = 107 °C, if there were no initial clearance?
Read with understanding and solve the following problem carefullyand honestly: Write your solution on a separate sheet of paper.1. In the figure, assume that a 20-mm diameter rivet joins the plates which are100 mm wide.a. If the allowable stresses are 140 MPa for bearing in the plate material and 80MPa for shearing of the rivet, determine the minimum thickness of each plate.(Ans. t = 9 mm) b. Under the conditions specified in part (a), what is the largest average tensilestress in the plates? (Ans. δt = 34.91 MPa)
A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a double parallel fillet weld. The maximum tensile and shear stresses are 60MPa and 50MPa respectively. Find the length of each parallel fillet weld, if the joint is subjected to static loading.
Example 10.11 The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction