design an interfacing circuit for the memory to meet the following specification: 1- Microprocessor have 16 address line 2- 74LS 138 :3 to 8 decoder 3- 2732 (4 K × 8) :EPROM -address range should begin at 0000 H and additional 4K memory space should be available for future expansion 4- 6116 (2K× 8): CMOS R/W memory And then identify the memory map

design an interfacing circuit for the memory to meet the following specification: 1- Microprocessor have 16 address line 2- 74LS 138 :3 to 8 decoder 3- 2732 (4 K × 8) :EPROM -address range should begin at 0000 H and additional 4K memory space should be available for future expansion 4- 6116 (2K× 8): CMOS R/W memory And then identify the memory map

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Interface 256KB EEPROM with 8088 microprocessor. Memory map for total EEPROM is 40000H and above. Your design must use NAND decoder. You are required to provide: A. Completely labelled schematic diagram to interface EEPROM with 8088 microprocessor. B. Starting and ending memory address of the memory chip. kindly provide its solution in handwritten form Regards MHR
assume that there are two memory chips one with capacity of 1MBx16 bit and another chip of 2GBx 8 bit are interfaced with cpu. determine the address and data lines required by CPU to access the memory chips. also draw suitable interfacing diagram
Draw a block diagram of a microprocessor-based system interfaced with 8255, 8254, 8259, 8237, and RAM. Also show clock generator, buffers, transceivers and address decoder in the diagram:use 8088 in minimum mode.
Assume a wafer has 300 mm diameter. It costs $20. Assume further that it contains 100 microprocessors and has a .05 defects/cm2.
microprocessor 8086 Design a control unit of a computer that has the following features: 16700 operations, 4 bits for indirect memory access, with memory size 128 GB X 64 bits. Then, show whether this design is perfect or has disadvantages. If does have, what are these disadvantages in this system Then, show the timing signals for the following: DLP MUL RI, where the MUL needs five clocks The MUL can't be run unless ADD R1,R2 is executed. ADD requires 3 clock cycles to be done Note that: among the 16700 operations, there are three operations require high time computation in which they require the following number of clock 102, 466, 20050 to complete only the clock execution section.
design a complete MIPS Processor(Datapath+Control Unit) for the following subset of MIPS instructions:ALU instructions (R-type): add, sub, and, or, xor, slt Immediate instructions (I-type): addi, slti, andi, ori, xori Load and Store (I-type): lw, sw Branch (I-type): beq, bne Jump (J-type): jthe internal circuit of all components used in the datapath(ALU, adder, Extender and ...) should be included in your design. You can use 32-bit adder, decoder , multiplexer, Memory, and Registers as the predefined component in your design
Topic : Writing MIPS code. 1.Consider the equation and write MIPS code for it: X=(A[4]+B[2])+(B[3]-5X); Assume array A stores floating-point values and its base address in $s0 and array B stores integer values and its base address is in $s1 register. X is in register $s2.
One of the three 4-bit Registers X, Y, Z via the 4-bit bus from one of the three 4-bit Registers A, B, CDraw a bus transfer circuit diagram to transfer 4-bit data to, and 4-bit from Register B to Register Z.Describe the process by which data is transmitted.
Assuming 8-bit memory addresses, show the active-high chip enable (CE) logic for a 32 x 8 memory module if its placement occupied the range of locations ... (a) 32 to 63 (b) 96 to 127
Consider a system that separates data and code. Two base-limit registers store and retrieve data for the central processor unit. Data and methods should be separated. Read-only pairs may be utilized by several users. Compare this strategy to others.
Design 16 bit of SRAM memory using 4X2 cell array also calculate each cell address
What memory address range is NOT represented by chip 1 and chip 2 in figure? A0 to A15 in this figure are the address lines and CS means Chip Select. (Gate 2005) Explain the program memory structure of 8051 microcontroller. Write an ALP using 8085 online simulator tool to perform logical XOR operation for two 8 bit data. Load the accumulator with 34 H and load the B register with 1AH.