Determine the density, specific volume, and volume of an object that weighs 3N 2 in water and 4N in oil with specific gravity of 0.83 draw figure

Q: ssify the following soils using the AASHTO classification system. Give group indexes as well.

A: Soil No.No.10No.40No.200Liquid limitPlastic…

Q: Determine the value of bending moment in column 3 (in kip-ft, absolute value) if the bay width is 20…

A:

Q: A one-way both ends continuous slab is to support the moments tabulated. Consider L= 5m. Fc’ = 21MPa…

A: L= 5mFc’ = 21MPafy = 415MPa.Dead load Moments: +42KN.m at midspan ;-67KN.m at support;Live Load…

Q: 9.3-23 The beam shown in the figure has a sliding support at A and a roller support at B. The…

A: Draw FBD:Calculate Bending moment equation:

Q: (3) and (4) Determine the reactions at supports. Assume "E" is constant. Draw the moment diagrams…

A: Given:Required:Support reaction and moment diagramNote: As per bartleby guidelines only first…

Q: The specific gravity of the soil is 1.41 ,percentage of water content by at field capacity and…

A: Specific Gravity= 1.41 =GField Capacity = 15% = 0.15=FCPermanent Wilting Point = 7%=0.07 = PWPRoot…

Q: 14. A contractor undertook to complete a piece of work in 120 days and employed 140 men upon it. At…

A: The contractor undertook to complete the work in initial  = 120 days.The first half employed (M1)=…

Q: A section of an OH line needs to be built on 46 ft. wood poles set 6 ft. deep in the ground. Each…

A: hag = Height of pole above ground = 46 - 6 = 40 fthbg = Height of pole below ground = 6 ft l1 =…

Q: Find the deflection using PARTIAL DERIVATIVE method 8 KN -3 m D -3m B 4 kN C

A:

Q: 3. The uniformly distributed vertical loads on the surface of a clay layer as shown in Figure below.…

A: For the given loaded area .We will first calculate the radial distance from point of consideration ,…

Q: The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes…

A: Given:Required:Force diagramMagnitude of concentrated force FCDTension forces in terms of TNote: As…

Q: Problem 3: IV Tube I Doctors use IV drips to deliver saline fluid (s = 1.2) into the vein of…

A:

Q: Problem 10.24 A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with…

A: Given Height 22.5 mTemperature 25°CLength 50 mDiameter 100 mmDepth 3 mTime 6.5 minutes To find out…

Q: All tapes should be standardised using: Question 17Select one: A. A reference tape   B. A…

A: All tapes should be standardised using:A. A reference tapeB. A baselineC. Both a and bD. A Boning…

Q: Find the magnitude of the internal shear force at point D for the given figure with a distributed…

A: Determine the internal shear force at point D.

Q: Correct

A:

Q: A settling tank has an overflow rate of 100,000 gal/ft² d. Water carrying se es enters the tank. The…

A:

Q: Given the simply supported beam below, and using the method of sections: 18 A t 1.5m C! 1.5m 1.5m KN…

A: Given:Required:Internal normal force at point D

Q: Calculate the slope and deflection atB and E of the beam and loadings shown using conjugate beam…

A:

Q: Determine the appropriate size of steel bars needed to confirm the development length requirements,…

A:

Q: to 3 m C 6 m 12 kN/m B

A:

Q: Which of the following are included when estimating equipment costs? Mobilization Idel time…

A: When estimating equipment costs, all of the options you provided—Mobilization, idle time, and…

Q: The internal normal force in kN at point C is mostly near

A:

Q: A beam is loaded and supported as shown, where F1=5 kN, F2 = 11 kN, M = 22 kNm, and a= 2 m.…

A:

Q: The truss below is to be analyzed using the Method of Sections. 2 kN A 4 kN 4 kN H 5m B -5m C G 5m 5…

A: Using method of section, the force in the member HG is

Q: 1.5 m E A -2 m- 3 kN D B -2 m- C

A:

Q: Question: Natural water content of a borrow material is known to be 8%. Assuming 5,500 g of moist…

A:

Q: Inclination angle = 23 degree 0.5 1 m с 0.5 p0.5 46ft g h 1 0.5

A: This truss is symmetric, We will analyse only half portion of truss as other corresponding members…

Q: The saturation flow for an intersection approach is 3600 veh/h. At the beginning of cycle no…

A: Solution:saturated flow rate;number of vehicles = 13 in the queueThe relation between the arrival…

Q: B f 900 lb 2 ft 200 lb/ft 6 ft The properties of the timber cantilever beam ABC are I = 60 in.4 and…

A:

Q: can you use Artesian formula

A: Given Radius of influence = 350 mdiameter = 30 cmlength = 25 mPermeability = 45 m/dayDrawdown = 4 m…

Q: Compute the moment inertia with respect to the X-X centroidal axis of the hollow-core pre-cast…

A:

Q: Water is pumped from the river through a 45-mm-diameter hose having a length of 3 m. The friction…

A: Diameter of the pump hose = 45mm = 0.045mLength                                   = 3mFriction…

Q: Pulley A has a weight of 30 lb and a centroidal radius of gyration kg = 0.40 ft. (Figure 1) Figure…

A:

Q: For the truss shown in the figure, the magnitude of the force (in kN) in the member SRis 30 kN I 1m…

A: The magnitude of the force (in kN) in the member SR is =?

Q: In Hooke and Brown's equation, If we have the value of m , how is the peak value of tensile strength…

A:

Q: 3: An equipment works on a road with a sandy clay soil with coefficient of traction (0.42). - Find…

A: An equipment works on a road with a sandy clay soil with coefficient of traction = 0.42The total…

Q: Calculate and plot the stress distribution with depth at a point 6.0 m from the corner (along the…

A: Calculate and plot the stress distribution with depth at a point 6.0 m from the corner (along the…

Q: After the soil samples are taken and the soil properties determined, the engineer must design the…

A: Project management  - Soil Samples, testing and designing a foundationthe soil sampling and testing…

Q: 2. A square footing has a dimension of 1.8 m x 1.8 m x 0.8 m. The column section is 320 mm square.…

A: The development length can be calculated using the following formula:Here,  and  are the…

Q: (1) Determine the reactions at supports "A", "B" and "C". The support at "A" is a pin whereas the…

A: Given:Required:Support reaction, shear-moment diagram

Q: A steel tape is 30 m long at a temperature of 15°C and a pull of 50 N when laid on a flat surface.…

A: Given data

Q: Cutting a structure is the most important step when applying Method of Sections. Which of the…

A: The rules pertaining to method of sections are given out of which correct options has to be choosen.

Q: 4- Design a concrete (n=0.012) trapezoidal channel carrying a discharge of 5 m³/s with a…

A: Discharge, Q = 5 m3/secLongitudinal slope, So = 0.0015 Channel section is Trapezoidal in shape with…

Q: An incinerator burns 180 lb/hr chlorobenzene and has a stack gas containing 7% oxygen by  volume on…

A: The objective of the question is to determine the percent excess air in the incinerator that burns…

Q: 5.66 For the beam shown in the fi above the bottom of the beam at secti A 1.5 m B 14 kN ,C 3 m

A:

Q: What is the correct shape for the shear diagram of member AB shown below:

A:

Q: en the beam below with constant El: KN A 5m EIOB, in kN-m. EIOC, in kN-m. MBC, in KN-m. ng…

A:

Q: hydraulics *use handwritten    A rectangular channel 5.50 m wide and 1.30 m deep is laid on a…

A:

Q: False! We do not need to worry about removing the effect of water from the soil weights to get the…

A: Effective stress is the stress carried by the soil skeleton independent of pore water pressure. It…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.