In Hooke and Brown's equation, If we have the value of m , how is the peak value of tensile strength calculated for granite, rhyolite, marble?? qu = 100MPa For marble (m = 7): peak compressive strength =? For rhyolite (m =17): peak compressive strength =? For granite (m = 25): peak compressive strength =?

In Hooke and Brown's equation, If we have the value of m , how is the peak value of tensile strength calculated for granite, rhyolite, marble?? qu = 100MPa For marble (m = 7): peak compressive strength =? For rhyolite (m =17): peak compressive strength =? For granite (m = 25): peak compressive strength =?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

Situation 1. From the given data of materials retained between consecutive sieves, compute the value of fineness modulus
(a) Define centroidal axes, principal axes and neutral axes with the help of diagrams. When do these axes coincide? (b) Define longitudinal and hoop stresses in a thin walled in thin walled pressure vessels. Support your answer with neat sketches. (c) Define strain gauge. Discuss strain rosettes and its various types. (d) Define Kern of a section. Derive the general equation for finding the kern of a section.
A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that the distance between the gage marks became 50.122mm. a,) What is the modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axial stress of the specimen?Note: Please show detailed solutions with illustrations.
Getting measurements from Figure, determine approximate values of the following items for plain concrete, concrete with 2% steel fibers, and concrete with 3% steel fibers:a. Modulus of elasticityb. Ultimate strengthc. Strain at failured. Toughness. Curves may be approximated with a series of straight lines.e. Comment on the effects of increasing the steel fiber content on items a, b,c, and d above.
A stone weighs 45Kg in air and 25Kg in water. Compute the volume of stone in cu. m. And What is the specific gravity of stone?
A hollow bronze cylinder is compressed by a P force. It has an internal diameter d1 = 1.85 in and an external diameter d2 = 2.15 in and a modulus of Elasticity E = 16000 ksi. When the P force increases from zero to 35Kip the outer diameter of the cylinder increases by 0.0017in. (a) determine the increase in internal diameter. b) determine the increase in wall thickness c) determine the poisson ratio for bronze.
With aid of diagram, elaborate on the method to test material hardness using Brinell hardness test
A stone weighs 650 N in air and 275 N in water. Compute its specific gravity.
A concrete has a height of 5 meters and has unit area of 3 m3 supports a mass of 30, 000 kg. Determine the following: Stress Strain Change in height Acceleration due to gravity (g) = 10 m/s2 Young modulus of concrete = 20x109N/m2
A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It isthen noted that the distance between the gage marks became 50.122mm. a,) What isthe modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axialstress of the specimen? Solution must have Free Body Diagram/drawing.
Consider a bar with a rectangular cross-section area with a thickness of t = 0.5 in. and height of h = 3.5 in. When force P = 19 kips is applied to the bar, the strain gages attached to the surface of the bar reads εx = 740 µε along the direction of the force and εy = -170 µε in the perpendicular direction. Determine Poisson's ratio for this specimen? Determine the modulus of elasticity for this specimen?in Ksi
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.