Determine the flow rate of air through an axial bush seal. The outer diameter of the inner cylinder is 250 mm and the radial clearance is 0.2 mm. The length of the seal is 100 mm. The pressures upstream and downstream of the seal are 1.5 and 1.01 bar, respectively. The viscosity of air can be taken as 1.85 x 10 Pas. m/s

Determine the flow rate of air through an axial bush seal. The outer diameter of the inner cylinder is 250 mm and the radial clearance is 0.2 mm. The length of the seal is 100 mm. The pressures upstream and downstream of the seal are 1.5 and 1.01 bar, respectively. The viscosity of air can be taken as 1.85 x 10 Pas. m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Complete the missing columns in the table and determine the experimental and theoretical values of the pipe friction factor using the respective formulae given above. Take the kinematic viscosity of water as 8.92x10-7 m2/s.
Carbon dioxide with a dpecifuc weight of 0.114lb/ft3 and a dynamic viscosity of 3.34 x 10^-7lb*s/ft2 flows in the shaded portion of the duct shown in fig 9.17. If the volume flow rate is 200ft3/min, calculate the Reynolds number of the flow. Answer is Nr= 2.77x10^4
A fan is used to force air having a temperature of 20°C through the 200-mm diameter galvanized sheet metal duct. Determine the required power output of the fan if the length of the duct is 150 m and the flow is to be 0.15 m3/s. Take f=0.023, density of air = 1.202 kg/m3, and kinematic viscosity of air = 15.1×10-6 m2/s.
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m³/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308x 10-3 Pa 's and 0.687x10-3 Pa s during the summer. What is the length of pipe necessary to reach a fully developed flow?
Determine the internal pressure of a liquid pipeline having an outside diameter of 8.625 in, a wall thickness of 0.5 in, and a yield strength of 32000 psi.
A crude oil of specific gravity 0.85 is flowing through a pipe of diameter 300 mm and the frictional head loss of 4.5 m of crude oil between the two ends of a pipe which are 700 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.0075 and kinematic viscosity as 14 stokes. 1) The velocity of flow of oil in the pipe is (m/s) 2) The Reynold's Number for the flow is 3) Discharge of crude oil through pipe (in m3/s) is
The head loss in 74 m of 150 mm diameter pipe is known to be 9 m when oil (s = 0.90) flows at 0.057 m^3/s. Assume viscosity of oil is 0.0389 Pa-s. Determine the Reynolds number. a. 19830 b. 15140 c. 11210 d. 13170
Fluid of density 1 030 kg/m3 and kinematic viscosity 1.86 x 10“5 m2/s flows parallel to a very smooth plane surface. The velocities at 75 mm and 4.4 mm from the wall are measured and found to be 0.3 m/s and 0.08 m/s, respectively. Using both of these measurements calculate the shearing stress on the surface.
When the free-flow velocity on the plate is 10 m/s, (a) when water with a kinematic coefficient of 1.14×10‾ⁿ (n=6) m²/s flows and (b) when air with a kinematic coefficient of 1.51×10‾ⁿ (n=5) m²/s flows, the flat plate How long can we assume that laminar flow is maintained from the front end of Critical reynolds number Re=50×10⁴
A pump is being used to transport a liquid food product (density = 1000 Kg/m3, viscosity= 1.2 x 10 -3 Pa-s) from a holding tank to a filling machine at a mass flow rate of 2 Kg/s. The liquid level at the holding tank is 5 m above the pump, and the filling machine is 10 m above the pump. There is 100 m of 2 inch nominal diameter sanitary pipeline (assume: commercial steel) between the holding tank and the filling machine with one open glove valve and three medium sweep 90oelbows in the system. Determine the theoretical power requirement of the pump if the efficiency is 75%. Answer: 234 Watts. Show the solution.
Question 2A large vat contains water, which contains a drainage pipe at a height h1, as shown infigure 2. The drainage pipe has a length L. = 0.4 m, and a radius R = 15 mm, and releaseswater to the atmosphere at a flow rate Q. The connection between the pipe and the vatwall has a loss coefficient of KL = 0.8.Point A is in the middle of the tank at a height, hi.You can assume that the flow in the drainage pipe is fully developed and laminar. The density of water is p = 1000 kg/m° and the viscosity is u = 1 mPa.s. The acceleration due to gravity is 9.81 m/s? a) Find an expression for the pressure at point A.b) Find an expression in terms of Q, L, d, K, p and u for the pressure losses along the pipe (including the losses at the inlet and exit).c) If the flowrate out of the drainage tank is Q = 50 L/min, find ho. You may assumeany change of ho with time is negligible.
What are the factors upon which the frictional loss in a pipe depends? For friction loss, how is the deviation between measured and theoretical values of f among the four segments of pipes? Which one has the largest deviations? Is reference values of KL is affected by the flow rate? Discuss the trend of deviation for KL when the flow rate increases for different pipe fittings.