determine the maximum bending and shear stresses at point C, at point P of the section. Represent the stress

Q: Determine the state of stress at point A on cross section a-a of the pipe, and sketch the stresses…

A: internal diameter (d1) = 0.75 in outer diameter (d2 ) = 1 in section properties : moment of inertia…

Q: Determine the principal stresses and the maximum shear stress correspondin the plane stress state…

A:

Q: Find the maimum normal stress carried in the part shown. 0-Sin ar0.5in

A:

Q: Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile…

A: Concept Of Moment Inertia Used

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

A:

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: The solid shaft is loaded (two point loads) and supported (fixed at left end) as shown. For the xyz…

A: AS this Question as multiparts solving first part or you can mention the part  Given data -: 1. dia…

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0=-30°…

A: Mohr's circle shows the transformation equations of the issues of planar stress. It is helpful to…

Q: QU For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: The average normal stress and maximum in-plane shear stress components are determined from the…

A: Yes, the average normal stress and the maximum in-plane shear stress components are determined from…

Q: Determine minimum principal stress

A: Given data : Normal stress in X direction (σX)=10 MPaNormal stress in Y direction (σY)=50 MPaShear…

Q: The internal loadings at a cross section through the 6-in.-diameter drive shaft of a turbine consist…

A: Given, Axial Load = -2500 lb Torsional moment (T) = 1500 lb.ft=1500 × 12 =18000 lb.in Bending moment…

Q: The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)…

A: (a) Write stresses that are shown in the element.   σx=240 MPaσy=100 MPaτxy=80 MPa

Q: Determine the maximum shear stress If maximum principal stress=50 MPa, Minimum principal Stress=20…

A:

Q: Determine maximum shear stress

A: Given data: σx=100 MPaσy=20 MPaτxy=40 MPa Need to determine the maximum shear stress.

Q: Determine the maximum shear stress in segment AB.

A: To find Maximum shear stress in segment AB

Q: 350 mm, tw = 7 mm, and h = 117 mm. Determine the principal stresses and the maximum shear stress…

A:

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses…

A: Given, I section Px =-80 kN = -80 X 103 N My=-500 Nm Mz=10 kNm =10 X 103 Nm

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0-30°…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

A:

Q: Determine the maximum shear stress magnitude in Segment (2). J1=

A:

Q: In each case, the state of stress sx, sy, txy produces normal and shear stress components along…

A: (a) sx'=-5 kPasy'=0τx'y'=8 kPau=20°   The stress along the normal -axis:…

Q: Using transformation equations of plane stress, determine the normal and shear stress components for…

A: The clockwise angle between the x’-axis and the x-axis is, θ=0.5 rad×180°π=28.65° The stress…

Q: Determine the average normal stress on the cross section. Sketch the normal stress distribution over…

A: Given: The magnitude of the force acting on the cross-section is F= 300 kN. The inner radius is…

Q: If u=15 kN/m, determine the following. a) Maximum tensile stress in the beam b) Maximum compressive…

A: Part A) Find the maximum bending moment of the simply supported beam as follows.

Q: Determine the average normal stress developed on the cross section as shown in Figure 1. 600 kN

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: Determine the maximum shear stress for the above stress state (ksi)

A: The matrix form of general 3D state of stress is

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: Given Data: The value of σx=125 MPa. The value of σy=-75 MPa The value of τxy=50 MPa. Part (a):…

Q: Determine maximum  principal stress

A: Given data: σx=10 MPaσy=50 MPaτxy=15 MPa Need to determine the maximum  principal stress.

Q: Determine maximum principal stress

A:

Q: 2. The coping saw has an adjustable blade that is tightened with 8 mm a tension of 40 N. 3 mm A 75…

A:

Q: b) The maximum in-plane shear stress and average normal stress. Sketch the results on a properly ori…

A: A: Formula:

Q: The sign is supported by a hollow structural tube of 15 in. outer diameter and 0.5 in. wall…

A:

Q: The axial and circumferential stress experienced by the cylinder wall at mid-depth

A: Given data: Axial stress on side face will be due to force on the bottom face.

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Consider the diagram shown in the figure. Here, σx=0, σy=-15ksi, τxy=-6ksi, θ=150°. We need to find…

Q: 4. The shaft shown transmits 1 kW of power at 1000 rpm. Determine the maximum stress in the shaft.…

A: ANS: power P= 1kW speed N=1000 rpm Torque T= 60*P/(2*π*N) =60*1/(2*π*1000) T=0.00954 N-m shear…

Q: A helicopter's rotor shaft has the hollow circular cross section shown as follows. The shaft is…

A: Calculated principal stress  and  absolute maximum shear stress at point p.

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

A: Given Data: The load acting on the beam is 25 kip each. The free-body diagram of the beam can be…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load…

A: Given:P=20 KNT=10.11 KN.md=75 mmdA=50 mm

Q: Draw mohr circle and determine maximum and minimum principal stress

A: Given data : Normal stress in X direction (σX)=-75 MPaNormal stress in Y direction (σY)=100 MPaShear…

Q: Determine the average normal stress on the cross section. Sketch the normal stress distribution over…

A:

Q: Determine the normal stress and shear stress at a point distant from hP from the bottom surface of…

A: Centroidal axis distance y= A1y1+A2y2+A3y3A1+A2+A3(1) A1=A2=(190) (10) =1900 mm2A3=(150)…

Q: At poin A Determine the Principal Stresses 01,02 Determine the Maximum Shear Stress Tmax

A: