Determine the set over to machine a taper cylinder with a major diameter 32 mm and minor diameter as 18 mm. The length of the job is 225 mm and the full taper angle is 14 degrees.

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: In the form tool used for creating taper, the tool is fed _________to the axis of lathe.

A:

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

A:

Q: 13.Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it…

A:

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an…

A: there are 4 subparts posted above.As per honor code and answering guidelines I can answer 1st three…

Q: 1. What type of milling machine can be used to make the groove in the shaft? 2. The diameter of the…

A: 1. Grooves, elongated slots and break-throughs are produced or made for the purpose of receiving…

Q: rm with two teeth drives a gear with 50 teeth. The gear has a pitch diameter of 8 in. and a helix…

A:

Q: a orthogonal Turning lathe machine of diameter rod of 100 mm, Rake angle: +15°,Uncut chip thickness…

A: Given values:Orthogonal turning is given,Rake angle,α=+15odiameter of rod,d=100 mmuncut chip…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given: cutting speed is 22 m/ minute. feed is 0.2 mm/ revolution. Depth of cut is 0.5 mm.

Q: )Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given d=22mm=0.022m spindle speed N=210rpm

Q: The distance measured along the pitch circle of gear from a point on one gear tooth to the…

A:

Q: Indicate the correct and incorrect methods of sectioning of machine elements represented below (Give…

A: b. corrected When the object is complex inside there When the object is complex from inside, there…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Metric thread of 0.8 mm pitch is to be cut on a lathe. Pitch of the lead screw is 1.5 mm. If the…

A: The speed of rotation of the lead screw is 800 rpm.

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut…

A: In turning operation the cutting force is the resultant of tangential force, feed force, and radial…

Q: 26. When a two-fluted end mill is used to cut a slot, the maximum depth of cut should be Select one:…

A: Option a is correct.

Q: The radial distance between the pitch circle and the top of the teeth is known as_ O a. Dedendum O…

A: Dedendum : It is the radial distance from the root circle to pitch circle.  Clearance: It is the…

Q: Determine the number of strokes per minute at which the shaper should run to machine a piece of…

A: The number of strokes per minute at which the shaper should run to machine a piece of copper is 96…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A:

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: Q3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the…

A:

Q: It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If…

A: Given data: Pscrew thread=2 mmPlead screw=6 mmNs=60 rpm Need to determine the speed of lead screw.

Q: A 3 inches diameter steel shaft rotates at 215 rpm. if the shearing stress is limited to 14 ksi,…

A:

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: The blade on a typical table saw rotates at 3100 revolutions per minute. Calculate the linear…

A: Calculated the linear velocity in miles per hour of one teeth at the edge of the 10 inch diameter…

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: A chain and sprocket has a pitch diameter of 30 inches and with 90 teeth available. Find the pitch…

A: Given data, D = 30 in     ( D = Pitch diameter ) T = 90          ( T = no. Of teeth ) Find pitch = P

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: A circle of 60 mm diameter rolls on the circumference of another circle of 200 mm diameter and…

A:

Q: 3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a…

A: (a) The feed rate in inch per minute is 15.28 in/min. (b) The cutting time omitting the over travel…

Q: mm/revolution is the unit of O a. Feed O b. Spindle speed O c. Cutting speed O d. Depth of cut

A: We have to solve unit conversation

Q: Determine the set over to machine a taper cylinder with a major diameter 32 mm and minor diameter as…

A:

Q: Calculate the outer diameter using compound method if the minor diameter is 28mm. angle of taper is…

A: We have to determine  1.draw the diagram and label the dimensions.

Q: D d. a° L1 El. Parameter in Dimension in lo: Drawing mm d 35 L1 28 |Cutting speed (Cs) in m/ minute…

A:

Q: In the gear drive the addendum circle diameter of the gear is 300mm and the dedendum circle radius…

A:

Q: A chain and sprocket has a pitch diameter of 9.56-inch and pitch 1/2-in .How many teeth are there in…

A: Given data, D = 9.56 in (D = Pitch diameter ) P= 0.5 in (P = Pitch) Find T = no. Of teeth = ?

Q: In a taper turning operation 35 is the diameter of the large end in mm, 25 is the taper angle in °…

A:

Q: The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of…

A: Given:p=4 mmθ=60°

Q: The blade on a typical table saw rotates at 3850 revolutions per minute. Calculate the linear…

A:

Q: Calculate the taper angle if the major diameter is 48.00mm and minor diameter is 28.00. The length…

A:

Q: Q2 -Calculate the taper angle if the major diameter is 40.00mm and minor diameter is 28.00. The…

A:

Q: The workpiece in turn in the taper in the lathe with.875 taper per foot. If the work has 4.8 large…

A: Given, tpf=0.875, D1=4.8" Find  D2

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20…

A: Soln:- depth = 20 mm            Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V=…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given dataCutting speed Vc = 22m/minFeed f = 0.2mm/revolutionDepth of cut d = 0.5mmTaper angle α =…

Q: Given a workpiece below all dimension are in inches. Determine: (a) the taper length of section A,…

A: Given : To find :  (a) the taper length of section A, (b) the degree setting to taper turn section…

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.