Answered: A shaft drives a gear set that is…

A shaft drives a gear set that is transmitting 5 hp at 1750 rpm. The diameter of the shaft is 0.75 in. Determine the torsional shear stress developed in the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Related questions

Q: A compound shaft is made by mounting a brass sleeve on a steel shaft (which is considered as…

Q: A solid 22 mm diameter shaft is used to transmit 128 Nm torques applied to gears. Determine the…

A: Given Data : Torque transmitted (T)=128 n-m R=0.011 Diameter of shaft(d)=22 mm=0.022 m

Q: A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the…

A: Power, P = 120 kW Speed, N = 200 rpm Tmax = 1.2Tmean Shear stress, = 70 N/mm2…

Q: A motor driving a solid circular steel shaft transmits 85 horsepower to a gear at point B (see…

Q: The steel shaft has four gears with corresponding number of powers as shown. The allowable shear…

A: Find the minimum required diameter of shaft Allowable shear stress = 75 Mpa Allowable twist = 0.05…

Q: A solid steel shaft AB shown in Fig. 5-13 is to be used to transmit 5 hp from the motor M to which…

Q: Compare the weights of equal lengths of hollow shaft and solid shaft to transmit a given torque for…

Q: Determine the torsional shear stress in a solid circular shaft having a diameter of 1.25 in. that is…

Q: 5. A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12 ksi. If the…

Q: Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively.…

A: Given data as per question Power of gear B =15 KW Power of gear A =6 KW Power of gear C =4 KW Power…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when ted to a torque of 12…

A: Given Twist angle = 30 Length = 6m Torque = 12 kNm Modulus of rigidity = 83 GPa To find Smallest…

Q: In the figure shown below, set F1 710 lb, F2 = 120 lb, F3 = 320 lb, the shaft diameter to 0.5 in,…

A: Given: The force along the x-axis, F1 = 710 lb The force along the y-axis, F2 = 120 lb The force…

Q: The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73…

A: find the maximum shear stress in the shaft.

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

Q: 03: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

A: The given question belongs to the topic Torsion of circular shafts. In this question, rotation given…

Q: a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the…

A: Given Data⇒ Hollow shaft Maximum torque : Tmax=4750 N-m Shear stress in shaft : ζ=50 Mpaζ=50×106Pa…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: A hollow steel shaft, 5.6 ft long, has an outer diameter of 3.02 in. and an inner diameter of 1.5…

Q: Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Given:P=30 KWζ=40 MPa

Q: Situation 24: The shaft is made of A992 steel (G = 75 GPa) and has an allowable shear stress of taow…

A: Given data: The shear modulus of steel shaft is G = 75 GPa. The allowable shear stress is τallowabe…

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: The A-36 steel shaft with a diameter of 30mm is supported on smooth bearings that allow it to rotate…

A: Given: The diameter of the shaft, d = 30 mm = 0.03 m The modulus of elasticity of the A36 shaft, G =…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 255 lb-ft and TD= 95 lb-ft,…

Q: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The…

A: Given, PB = 15 kW E = 200 GPa ν=0.3 f = 6 Hz

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.…

A: Given data: Maximum torque, T = 4750 N·m. Shear stress in the shaft, τ = 50 MPa. The ratio of…

Q: Determine the required minimum diameter d of the shaft to the nearest millimeter. Express your…

Q: The design of a machine element calls for a 40-mm-outer-diameter shaft to transmit 50 kW. If the…

A: As there are two shaft shown in figure but for figure b , d2 is not given so I have considered…

Q: 3.The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. If gear B…

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

A: GIVEN: WORKING SHEAR STRESS, τ= 64MPa diameter of disc A=250mm diameter of disc B=500mm diameter of…

Q: 1) A solid steel drive shaft is required to transmit 12 hp. The allowable shear stress for steel is…

Q: Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it…

Q: A 2-in-diameter steel shaft rotates at 240 rpm. If the shearing stress is limited to 12 ksi,…

A: Diameter, D= 2 in Speed, N= 240 rpm= 24060 rps Shearing stress, τ= 12 ksi= 12(1000) lbf/in2= 12000…

Q: The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of…

A: Given data as per the question Length of shaft =6 m Power delivered =4 MW The outer diameter of the…

Q: A solid circular shaft has a uniform diameter of 2" and is 10 ft long. At its midpoint, 65hp is…

Q: The solid 35-mm-diameter shaft is used to transmit the torques applied to the gears. The shaft is…

A: Given data: To determine the maximum torque, draw the torque diagram for the given system. Thus,…

Q: The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the…

A: Given: The allowable shear stress, τ = 75 MPa The speed of the shaft, N = 300 rpm The power of the…

Q: A 4-m long shaft transmits a torque of 5 kN-m. Determine the maximum torsional stress (TMax) of the…

A: Given: length of the shaft→L=4m torque transmitted→T=5 KN‐m=5000 N‐m outer diameter of the…

Q: Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also…

A: Given data, P= 112.5 kW =112500 W N= 200 rpm. θ=1.5° =0.0261799 rad. τ=55 N/mm² =55000000 N/m²…

Q: The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum…

Q: i) the torque acting on the shaft; ii) the required external and internal diameters for the shaft;…

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

A: P=15000Hp N=300rpm

Q: A gear motor can develop 2010 W when it turns at 231 RPM. If the allowable shear stress for the…

A: Given:P=2010 WN=231 rpmζallow=88.3 MPaP=2πNT602010=2π*231*T60T=2010*602*π*231T=83.09 N.m

Q: A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of…

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m…

A: Given data Maximum torque (T) = 4750 N-m limited shear stress (τ) = 50 MPa Inside dia to outside…

Q: For a given maximum average shear stress, determine the factor by which the torque-carrying capacity…

A: The mean area without reversed position Am=(1.10)1.75-π(0.55)22=1.4498 in2 The mean area at reversed…

Q: A hollow steel shaft, 5.7 ft long, has an outer diameter of 3.1 in. and an inner diameter of 1.53…

A: To find : determine the maximum shear stress. Given : lenght of shaft L=5.7ft outer diameter…

Q: 3.The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. If gear B…

Q: A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75…

A: Given dataPower transmitting capacity of the shaft P = 8hpRotation of the shaft N = 2250 rpmDiameter…

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

A shaft drives a gear set that is transmitting 5 hp at 1750 rpm. The diameter of the shaft is 0.75 in. Determine the torsional shear stress developed in the shaft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.
A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not amount to 500MPa, determine the size of the shaft.
Motor A develops a power of 300 W and drives a pulley at 90 rpm. Determine the required diameters of the steel shafts that drive the pulleys A and B if the allowable shear stress is τ perm = 85 Mpa.
A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the shaft material is 56 N/mm2. Determine the diameter of the shaft?
A shaft is made of an aluminum alloy having allowable shear stress of tallow = 100 MPa. If the diameter of the shaft is 100 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T if a 75-mm-diameter hole were bored through the shaft? Sketchthe shear-stress distribution along a radial line in each case.
In the geared shaft shown below, gears A and B and gears C and D are separated by 500 mm. Gears B and C are separated by 400 mm. Gear A is experiencing a 250N⋅m250N⋅m clockwise torque; gear B is experiencing a 75N⋅m75N⋅m counter-clockwise torque; gear C is experiencing a 325N⋅m325N⋅m counter-clockwise torque; and gear D is experiencing a 150N⋅m150N⋅m clockwise torque. What is the absolute maximum shear stress in the shaft (in MPa) if the shaft has a 50-mm diameter?
a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the shear stress in the shaft is limited to 50 mpa. determine the inside outside diameter of the shaft if the ratio of inside to outside diameter of the shaft is 0.4
A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside diameter 0.6 times the outer diameter. It is made of plain carbon steel and the permissible shear stress is 84 N/mm^2. Determine the inner and outer diameters of the shaft.
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft rotates at a speed of 679 rpm and transmits a power of 5 kW. If the maximum torque exceeds the mean torque by 23%. Take the value of allowable shear stress as 71 MPa. Find the value of the following i) Torque transmitted in N-m ii) Maximum torque transmitted in N-m iii) Diameter of the shaft in mm.