Determine the value of supply voltage for a DC Series Motor having back EMF of 206.2V with armature resistance of 0.6 ohms, series field resistance of 1.4 ohms and motor current of 16.5A. a. 193.00 V b. 239.20 V c. 219.40 V d. 173.20 V

Determine the value of supply voltage for a DC Series Motor having back EMF of 206.2V with armature resistance of 0.6 ohms, series field resistance of 1.4 ohms and motor current of 16.5A. a. 193.00 V b. 239.20 V c. 219.40 V d. 173.20 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Related questions

Q: Q/ dc shunt motor 4 pole with 500 condcutor, wave running at speed 1000 r.p.m the resistance of…

Q: The field and armature resistances of a 231V series motor are 0.1 ohm and 0.2 ohm, respectively. The…

A: Find the efficiency of the motor . If armature and field winding resistance = 0.1 and 0.2 ohm Motor…

Q: Q1/Prove that the power developed by a three-phase induction motor is maximum when the equivalent…

A: The Thevenin equivalent circuit of a 3 phase induction motor can be represented as, now,…

Q: 7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750…

A: Given a short generator with speed of 750 rev/min. From the given values in table, we draw graph of…

Q: A 220 V dc short-shunt compound motor draws a rated line current of 60 A. The armature, series field…

Q: A 230 V D.C. shunt motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of…

A: The solution can be achieved as follows.

Q: Exam -2021 ARall.stio Anser all questions QLA: The following data apply te a 100-AW 250-V sis-pole,…

A: Calculate the load current of the generator. IL=PoutV=100×03 W250 V=400 A

Q: Calculate the value of supply voltage for a DC Series Motor having back EMF of 206.2V with armature…

A: In a DC series motor, the field winding is connected in series with the armature winding and carries…

Q: The power supplied to a three-phase induction motor is 50 kW and the stator losses are 2 kW. If the…

A: Given values are - Pin=50kWStator losses=2kWSlips=4%=0.04Friction+Windage Loss=1kW

Q: 1. A 240-V d.c. shunt motor has an armature resistance of 0.4 2 and field resistance of 110 Q. At no…

Q: eld resistance is 52.5Ω and the series field resistance is 0.1Ω. if the SPL amounts to 631W,…

Q: 9. A 250 V DC long-shunt, compound motor takes a current of 82 A at full load. Calculate the motor…

Q: A single-phase semiconverter controls a DC motor. The ac supply voltage to the armature and field…

Q: A three-phase alternator, 2500KVA, and 2400 volts operate at rated kilovolt-Ampere at a power factor…

A: Given data is shown below. Output =2500kVALoad power factor =0.8line volatge =2400VField current=70A…

Q: Determine the efficiency of a 1500kVA, 2300-V, 3-phase, Wye connected alternator, which operates at…

A: The alternator is a doubly-fed Motor in which the Main field is excited by DC supply and the…

Q: A 3-phase, 6-pole and 50Hz induction motor has a speed of 955d/min under full load, a torque of 120…

A: we will take ratio of starting and full load torque and starting torque to find starting torque

Q: See attached.

A: (a)Assume ra = 0, then Eb1= Eb2 = terminal voltage = VT = 125 V.

Q: The speed of a 230 V shunt motor is to be reduced from 900 r.p.m to 600 r.p.m. The resistance of the…

A: Given Terminal voltage (VT)=230 vspeed (N1)=900 rpmArmature current (Ia1)=30 AArmature…

Q: single-phase induction motor employed for a mechanical work at a rate of 45 HP. Its electrical power…

Q: A 200V long-shunt generator delivers 100A, has an armature resistance of 0.05Ω, a series field…

Q: The field and armature resistancesofa 220-V series motor are 0.2 ohm and 0.1 ohm , respectively. The…

A: Efficiency = (output power/input power)×100. Input power = terminal voltage ×current drawn by motor.…

Q: 250 V D. C shunt motor takes 41 A at full load, Resistances of motor armature and shunt field…

Q: A 230 V D.C. shunt motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of…

Q: A 240V shunt motor, running on no-load and at normal speed, takes an armature current of 2.4 A from…

Q: Re Q2 // A series motor has an armature resistance of (0.4 92 ) and a series field resistance of (…

Q: 7. A 50 kVA, 230V, 50HZ alternator has as effective armature resistance of 0.0122 and an armature…

A: Need to find generated voltage of given alternator with given power factor condition

Q: The following test results are obtained from a 3 -phase, 4800KW, 6600V, star connected, 2 pole, 50…

Q: Home Work 15: A 3-phase, 6600 V, star-connected, synchronous motor draws a full-load current of 70 A…

Q: 381 V, four pole, 50 Hz, Y connected, to an asynchronous motor with a nominal power of 13.8 HP The…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: A separately excited DC motor with supply voltage of 420 V, armature resistance of 0.5 N and K_ =1.8…

A: Given data A separately excited DC motor is controlled by a regenerative braking using a DC chopper.…

Q: Homework problem (1): A 3-phase, star connected synchronous motor of 10 kW at 1100 V has synchronous…

A: Given machine is 3-phase synchronous motor. The terminal phase voltage is Vtph=11001.732=635.1039…

Q: Three-phase asynchronous motor with a nominal value of 20 kW, 6 poles. It has a voltage value of 420…

A: In this question we need to find a total copper losses and the shaft torque of the given induction…

Q: A 30-kW, 250-V dc long shunt generator has armature, series and shunt field winding resistances of…

A: Ra=0.065 ΩVt=250 VRse=0.10ΩRsh=12.5Ωηmax.=87.77%Ish=VtRsh=250125=2AIsh=2ALoad power…

Q: 200V shunt generators has an armature resistance of 0.02ohms and a shunt resistance of 50ohms. At…

A: In this question we will find armature current of dc shunt generator.....

Q: Q2) Determine the back e.m.f at this load of series motor has a series field resistance of (0.301 2)…

Q: A de shunt motor operating unloaded at a terminal voltage of 125V at a speed of 1420 rpm. When the…

Q: A short-shunt generator supplies 220A at 260V. The armature resistance is 0.15Ω, shunt field…

A: The solution is given by

Q: Answe completely and elaborate complete details. No plagiarism 1.) Define the working principle of…

A: AC motor: The motor converts the electrical current into mechanical power. This type of motor is…

Q: Using the D.C. shunt motor no-load and full-load information given in the following table, determine…

A: The solution is given below

Q: 13 kW, 198 V DC short-shunt motor, being fed through a feeder with total resistance of 0.04 ohms,…

Q: 5- In a 3-phase induction motor, if the supply voltage and frequency afe reduced by the ratio, then…

A: The speed depends on the supply frequency that is : Synchronous speed (N)=120fP

Q: 7. A 250 V DC long-shunt, compound motor takes a current of 82 A at full load. Calculate the motor…

Q: 24. NEMA-rated general-purpose motors can operate on voltages 610% of their rated nameplate voltage.…

A: Consider the voltage between the phases AB is, EAB=465 VThe voltage between the phases BC is,EBC=487…

Q: 440v, shunt motor has armature resistance 0.8ohm and field resistance of200ohm Determine the back…

A: Given, Terminal voltage of shunt motor = 440 V Field resistance of Shunt motor = 200 ohm Armature…

Q: Find the starting current (in Ampere) of 148 V DC series motor if the armature resistance = 0.6 ohm…

A: V=148 V Armature Resistance=0.6 ohm Field Resistance=0.2 ohm

Q: The nameplate data on a drive motor for an air supply fan gives the rating of the 4 pole drive motor…

A: Given data- Speed of fan N1=1480 rpmMotor KW P1=135KW After reduction of flow through guide vanes by…

Q: 14. For an ideal gearing system, with N1 and N2 are the numbers of the teeth in the gear wheels the…

A: Given Ideal gearing system Number of teeth in mechanical load is N1=40Number of teeth in motor side…

Q: .) A 25-kW shunt generator is delivering full output to 400-V bus-bars and is driven at 950 r.p.m.…

A: In this question, find the speed uf machine act as motor? A 25-kW shunt generator is delivering…

Q: dc shunt generator in an open-circuit condition has a voltage of 240 V. Its full-load voltage is 230…

A: In this question we will find dc generator load current with given data..

Q: 415 V Shunt motor takes a total current of 80 A . if the shunt field resistance is 40 ohms, the…

A: In this question. We will find cu losses , output power and efficiency..

Question

Determine the value of supply voltage for a DC Series Motor having back EMF of 206.2V with armature resistance of 0.6 ohms, series field resistance of 1.4 ohms and motor current of 16.5A.

193.00 V

239.20 V

219.40 V

173.20 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 489V shunt motor delivers 30hp at the shaft at 1120rpm. If the motor has an efficiency of 86% at this load, determine the (a) total input power and (b) line current.
A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power. Find the load angle?
A 6-phase ∆-connected 1600 V (line-to-line), 150 kW, 50 Hz, six-pole induction driveis used in an electric car. The drive has the following parameter values in Ω/phasereferred to the stator:R1 =0.334 Ω R2 =0.168 Ω Rm1 = 125 ΩX1 = 0.273 Ω X2 = 0.287 Ω Xm1 = 16.78 ΩThe total friction, windage, and core losses may be assumed to be constant at Prot =773 W, independent of load. For a slip value of s=0.015: b ) Compute the speed, output torque, power and stator current d) Calculate the efficiency when the motor is operated at rated voltage andfrequency. answer：b) n= 985 rpm; Torque T= 1.18 x104 Nm; Power= 1.22 x106 W; Stator current I = 175.72 /32.79° (d) Efficiency = 86.4%
A shunt generator has an external characteristic whose terminal voltage is given by the equation VT = 240 – 0.5IL, where IL is the load current and RL=12Ω, what is the value of the terminal voltage VT (in Volts).
Incremental fuel cost of a generator is given as 3 P12+ 40 P1 +90 $/MWh. Give the cost function and Calculate the operating cost of the generator for meeting 100 MW, if the fixed cost is 20$/h?
A 16-cylinder, 39.37cm x 55.88cm x 327-rpm, 4-cycle stationary, diesel engine is connected to a 3,125 KVA (80% Power Factor) generator. It also drives a 30-kW exciter. Assume a generator efficiency of 92% and determine the Break-Mean-Effective-Pressure (BMEP), in kg/cm2, at rated load.
4. Two shunt generators operating in parallel have each an armature resistance of 0.02 . The combined external load current is 2500 A. If the generated e.m.fs. of the machines are 560 V and 550 V respectively, calculate the bus-bar voltage and output in kW of each machine. Subject: Electrical Machine 1
Electrical Engineering A wye-connected synchronous motor connected to a 440V, 3-phase line is operating with an electrical load (torque) angle  of -28 degrees while demanding 90 kW from the mains. The motor has negligible resistance and reactance of 1.5 Ω/ph. Calculate: (a) The line-to-neutral excitation voltage (b) The line current and power factor.
A 6-phase ∆-connected 1600 V (line-to-line), 150 kW, 50 Hz, six-pole induction drive is used in an electric car. The drive has the following parameter values in Ω/phase referred to the stator: R1 =0.334 Ω R2 =0.168 Ω Rm1 = 125 Ω X1 = 0.273 Ω X2 = 0.287 Ω Xm1 = 16.78 Ω The total friction, windage, and core losses may be assumed to be constant at Prot =773 W, independent of load. For a slip value of s=0.015: a) Draw the equivalent circuitb) Compute the speed, output torque, power and stator currentc)Determine the power factor and whether leading or lagging d)Calculate the efficiency when the motor is operated at rated voltage and frequency.
Q20) A 1000rpm DC shunt generator is supplying 100 lamps of 60W at 230V, the armature and field resistance are respectively 0.1Ω and 115Ω.Calculate the generated emf. a. 232.809 V b. 222.809 V c. 212.809 V d. 242.809 V
A self-excited DC shunt generator is delivering20 A to a 100-V line when it is driven at 200 rad/s.The magnetization characteristic is shown inFigure. It is known that Ra = 1.0 Ω andRf = 100Ω . When the generator is disconnectedfrom the line, the drive motor speeds up to 220 rad/s.What is the terminal voltage?
For one-phase appliance of R-L type (e.g. electrical motor) with active input power P = 10 kW and power factor cosϕ = 0,75 design a power-factor capacitor to compensate the power factor to the standardized value of cosϕk = 0,95. Supply voltage is V = 230 V. Calculate capacitor reactive power, its capacity and current.