Answered: Determine the velocity of flow and the…

Determine the velocity of flow and the friction loss as 0.472 m3/s of air flows through 23 m of an 0.305 m-diameter round duct V-65.mla DoltoD 41. S Do

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Fig. Shown three tanks, tank 1 without an orifice tube and tanks 2 and 3 with orifice tubes as…

A: Given that, three tank has different height of water For tank 1 total height is H For tank 2 ,…

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f=0.0225) of length…

Q: Determine the head loss due to a sharp-edged pipe inlet if water is flowing 27.7 ft/s.

A: Given Data V=27.7 ft/s=8.44 m/s

Q: Fluic Determine the rate of flow water through a pipe 300 mm dimeter placed in an inclined Position…

Q: Determine the pressure drop per 100-m length of horizontal new 0.30-m-diameter cast iron water pipe…

Q: Select duct sizes for the rectangular duct system shown in the Figure, using the equal friction…

A: Given DataL=6mTotal pressure of the Duct=30PaPressure of Each Diffuser=5Pa Given System

Q: Calculate the horizontal force acting on the conical part of the pipe! $50 mm = 3.5 m' / min O 200mm…

Q: Determine the average velocity for water flow in a 20 mm diameter copper tube (21.4 mm outside…

A: Given data:

Q: Q:- Prove that the angle of inclination of two fixed parallel plate as shown in fig, so that laminar…

A: Navier stokes equation for plane Poiseulli's flow is valid for this problem. Several assumptions…

Q: نقطة واحدة If the flow is laminar and Reynolds number = 1* 103, then the friction * ?-- =factor…

A: Given data: Re=1×103 Need to determine the value of friction factor.

Q: expressions for total flow rate (Q) and frictional head loss across the two ends (h₁) are

A: Given, 3 parallel pipes connected at two ends have, flow rates= Q1,Q2 and Q3…

Q: A sharp-edged orifice in the vertical wall of a large tank has a diameter of 25 mm. The coefficient…

Q: A complete rough rectangular pipe (e-0.9mm) of cross sectional area (a X b). Determine the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: A farmer is to pump water at 70°F from a river to a water storage tank nearby using a 125-ft-long,…

A: Write the properties of the water at 70°F. Write the properties of galvanized iron. Write the…

Q: 13. For the same value of Reynolds number friction factor for steady laminar for circular pipe is…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Q.1 A horizontal tube of 60 m lenght is connected to a water vessel at one end discharges freely…

A: Given: Total length of pipe= 60 m Length of 1st pipe, L1= 35 m Diameter of the 1st pipe, d1= 0.12 m…

Q: DETERMINE THE PRESSURE TO HAVE A DISTANCE: 600m CONSISTENT AND COMPATIBLE FLOW RATE Raver ELEVATION:…

A: Given: Total length of the pipe: →L=600 m Height of the water tank from the river surface: →H=100 m…

Q: Q5:Oil flows in a pipe 80 mm bore with a mean velocity of 5 m/s. The mean surface roughness is 0.02…

Q: 1. Given that the transition Reynold's number for flow in a duct is 2300, the smallest pipe for…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 4- When the coefficient of discharge of negative relationship with coefficient of contraction. 5-…

A: (4) Write the expression of coefficient of discharge in terms of coefficient of contraction.

Q: The piping arrangement shown delivers a jet of water at location C. Water enters the pipe from ne…

A: given minor coefficient bwtween A and B , KAB=7minor coefficient bwtween B and C , KBC=3Diameter of…

Q: Water flows at a rate of 0.185 m3/s through a 150 m long galvanized steel pipe of diameter 200 mm.…

Q: QI: A closed tank partially filled with water up to a height of 0.9 m having an orifice of diameter…

Q: The average velocity of water flowing in a circular pipe of 5cm in diameter is 3m/s. If the flow is…

A: The mean velocity is factor defined by discharge but in actual condition the actual velocity is more…

Q: Determine the power required (Watts) to drive a reciprocating pump running at 1 rps and discharges…

A: Givenρ=850 kg/m3Q=366.1 gpmd=250mmL=500mmH=39m

Q: Water flows from section 1 to the reservoir at section 3 (where V3 = 0 ft/s) through first 300-ft…

A: Given DataL1=300ft=91.44md1=2in=0.0508mL2=100ft=30.48md2=3in=0.0762mQ=40gal/min=0.0252m3/sTotal…

Q: 1. Calculate the power required at the pump shaft given that the wate density and flow rate are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 20 16 12 ft h, = 16 – 5Q %D e 12 8 Pump 4 1 2 Q, ft³ls 3 h, ft

Q: Calculate the head loss due to friction in a pipe of diameter 25 cm and length 60 m, through which…

Q: What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel…

A: Let us take free liquid surface as state 1 and the point where water is coming out as state 2. For…

Q: inwhich ris the local radius, Ris the radius of the inner wall of the pipe and Vawg is the average…

A: For solution refer below images. ∗From the given data V=2.Vavg 1-r2R2 ∗Velocity profile:-…

Q: Water flows through a new cast iron (e = 0.26 mm) pipe at a velocity of 4.2 m/s. The length and…

Q: Water flows into junction J from reservoirs A and Bthrough connecting pipes, the head loss through…

A: Given:Head loss in pipe A=10QA2Head loss in pipe B=4QB2water level at A=25.9 mwater level at B=18…

Q: Determine the maximum allowable volume flow rate in L/min that can be carried through a standare…

Q: Y A proposed hydroelectric plant is to have a flow of 200 cfs against a net head of 30 ft. The…

A: Given:Net head, H=30 ft or 9.144 mspeed, N=200 RPMPower ,P=450 kW

Q: A sharpe-edged orifice has a diameter of 25.4 mm and coefficients of veloc- ity and contraction of…

Q: Prove that the coefficient of friction for Hagen Poiseuille flow in a cylindrical pipe is equal to…

Q: Water flows through main pipe A at 300 kg/s, and then out the double wye with average velocities 2 r…

Q: A new cast-iron pipe 400 m long and 15 cm in diameter carries 42 L/s of water. Determine the…

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: What is the water flow rate (Q) of the shown pipe? Friction head loss is given by f = 0.2(L/D)v/2g.…

Q: A 150mmø pipe having a total length of 102m carries a discharge of 60liters per second as shown in…

A: Given: Diameter of pipe,d=150 mmTotal length of pipe,L= 102 mdischarge, Q= 60 Litresec=60×10-3…

Q: O , - S00 kP mm diameter 50- mm diameter Water

A: given:

Q: Water flow at a 250mm diameter horizontal pipe. The friction factor is 0.023. If the pressure at the…

Q: arrying water (p kg/m³; stokes) has of average height of 0.1 mm. If the shear stress develo ermine…

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A: The volume flowrate of fluid passing through a cross section can be determined as the product of…

Q: find the diameter through circular duct if the flow rate (0.98 m3/s) and velocity(5m/s) Fullcen Snip…

Q: kPa respectively The velocity and e head loss (hy) between the entry and

A: answer- b.1.92m

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?
During a retrofitting project of a fluid flow system to reduce the pumping power, it is proposed to install vanes into the miter elbows or to replace the sharp turns in 90° miter elbows by smooth curved bends. Which approach will result in a greater reduction in pumping power requirements?
A clothes dryer discharges air at 1 atm and 120°F at a rate of 1.2 ft3/s when its 5-in-diameter, well-rounded vent with negligible loss is not connected to any duct. Determine the flow rate when the vent is connected to a 15-ft-long, 5-in-diameter duct made of galvanized iron, with three 90° flanged smooth bends. Take the friction factor of the duct to be 0.019, and assume the fan power input to remain constant.
Explain how flow rate is measured with a turbine flowmeter, and discuss how they compare to other types of flowmeters with respect to cost, head loss, and accuracy.
Two vessels in which the difference of surface levels is maintained constant at 2.4 m are connected by a 75 mm diameter pipeline 15 m long. If the frictional coefficient f may be taken as 0.008, determine the volume rate of flow.?
A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total length of the 10-in-ID pipes is 62 ft. and the friction factor is taken as 0.022. If the pump head H can be defined as a function of discharge Q in ft3/s is: H = 365 - (0.04718Q^2), in feet. What is the operating discharge rate in ft3/s?
Air is flowing in a circular duct. The air flow rate is Q=2000 ft3/min. The diameter of the duct is D=14 in. (2) Determine the friction loss per 100 ft, hL_________inH2O
include a free body diagram Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet isA. 6.21B. 7.12C. 8.7D. 5.05
Can you use the friction factor for turbulent flow in a smooth circular tube to predict the fiction factor in an internally finned tube by using the hydraulic diameter?
What is the operating principle of variable-area flowmeters (rotameters)? How do they compare to other types of flowmeters with respect to cost, head loss, and reliability?
For flow of water at a Reynolds number of 1.03E6 through a 5-cm-diameter pipe of roughness height 0.5 mm, the approximate Moody friction factor is (a) 0.012 (b) 0.018 (c) 0.038 (d) 0.049 (e) 0.102
Water at 60°F (? = 62.36 lbm/ft3 and ? = 7.536 × 10−4 lbm/ft·s) is flowing steadily in a 2-in-diameter horizontal pipe made of stainless steel at a rate of 0.2 ft3/s. Determine the pressure drop, the head loss, and the required pumping power input for flow over a 200-ft-long section of the pipe.