A 150mmø pipe having a total length of 102m carries a discharge of 60liters per second as shown in the figure. The minor loss coefficients for the entrance, elbows and globe valve are 0.50, 0.90 each and 10 respectively. If the friction factor f=0.005. 150 mm e ciean cast iron pipe 12 m Globe valve

A 150mmø pipe having a total length of 102m carries a discharge of 60liters per second as shown in the figure. The minor loss coefficients for the entrance, elbows and globe valve are 0.50, 0.90 each and 10 respectively. If the friction factor f=0.005. 150 mm e ciean cast iron pipe 12 m Globe valve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
Two new cast-iron pipes (ε = 0.26 mm) in series connect two reservoirs. Both pipesare 300 m long and have diameters of 0.6 m and 0.4 m, respectively. There is a valvein the 0.6 m diameter line with K = 10. The elevation of water surface in reservoir A is80 m. The discharge of 10°C water from reservoir A to reservoir B is 0.5 m3/s. Find theelevation of the surface of reservoir B. Assume a sudden contraction at the junctionand the entrance and exit is sharp.
Water is pumped through a 60-m-long, 0.3 –m-diameter pipe from a lower reservoir to a higher reservoir whose surface is 10 m above the lower one. The sum of the minor loss coefficients for the system is Kl = 1.5. When the pump adds 40 kW to the water the flowrate is 0.2 m3/s. Determine the pipe roughness.
Determine the Reynold's Number and flow regime of an bil flowing through a 450-mm diameter pipe, if the flow rate is 0.40 m³/s. Note: Hoil = 0.025 Pa's and Scoil = 0.86).
Design the duct system shown below using Equal friction method, and determine the fan power when the fan efficiency is 68%. The duct is circular. Take the velocity in the main duct AB equal to 7 m/s. Assume a dynamic loss coefficient of 0.5 in T fitting and 0.8 in elbow fitting. Given AB = BC = 10m and BD = 25m .
Water at 10oC is to flow from reservoir A to reservoir B through a cast-iron pipe of length 20 m at a rate of Q=0.0015 m3/s as shown in Figure. The system contains a sharp-edged entrance and six regular threaded 90° elbows. Determine the pipe diameter needed.
The horizontal pipe length is 180 m and the vertical pipe length is 24 m in the fire protection system, which is formed with a water tower and pipeline, 1 threaded 90 ° elbow (Kd = 0.9) on the pipeline and 1 slide valve at the pipe outlet (fully open position Kv = 0.2). Since the pipe material is cast iron and its diameter is 4 ”(101.6 mm), determine the maximum flow rate in the pipe considering the losses. Assume that the water level in the tower remains constant and the kinematic viscosity of the water is 1.124x10-6 m2 / s. Show your readings by drawing on the attached Moody diagram.
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 286 liters per second. The total length of pipe connecting the two reservoirs is 186 m. The pipe diameter is 346 mm and the Hazen-Williams coefficient is 129. The water surface elevations of reservoirs 1 and 2 are 194 m and 69 m, respectively. Determine the power in kW required by the turbine if it is 63% efficient? Neglect minor losses. Round your answer to 3 decimal places.
Two pipes, one circular and one square have the same cross-sectional area. Which has the larger hydraulic radius ? Show your solution to prove your answer
Determine the Darcy friction factor f in a fully developed flow in a pipe (diameter = 0.5 ft) made of galvanized iron if Reynold's number is 50, 000.
Determine the discharge through three new cast-iron pipe connected in series, having diameters of 250mm, 200mm, 150mm and lengths of 600m, 360m and 270m respectively, When the total friction loss not including the minor losses is 5.0 m. Assume f=0.024 for all pipes.( hint: apply H= f.L.V²/( D.2.g)₁ + f.L.V²/( D.2.g)₂ + f.L.V²/( D.2.g)₃ and Q1=Q2=Q3 where Q=A.V ).
A 100m long pipe with diameter D = 20cm and CH/w= 120 carries a discharge of 30lit/sec. Determine the head loss in the pipe.