Draw SFD and BMD

Q: One of the following is not used to reduce the setup time? a. Using power clamp b. Using softer raw…

A: The setup time can be reduced by - Eliminating waste Using power clamp Design for manufacturability…

Q: draw it top and side sectional view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: = missing properties

A: Solution given below.

Q: chir

A:

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: vill become tu

A:

Q: dy y dx

A:

Q: S teath oulat

A:

Q: aHom a ncla with a spccd O. paads contal The distance it w

A:

Q: dv dy

A: first of all find out the shear stress = force/ Area. then apply newtons law of viscosity.for…

Q: In section views, hatch patterms should be drawn parallel to one of the edges of the part. True? A)…

A: In section views the hatch pattern should be drawn at an angle between 15o to 75o but not parallel…

Q: a) VB= i m/s

A: To determine vB and NA

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: Differentite between enclosure hoods, canopy hoods, and capturing hoods.

A: A capturing hood is a device that channels the outflow of air from an air conditioning system. It…

Q: "Sarcomere"

A: option b) part between two Z line

Q: aber of teeth for involute

A:

Q: Write down the name of Primary Control Surface

A: The rudder is a fundamental control surface which is typically controlled by pedals rather than…

Q: norizontal

A: given:

Q: The value of FPQ

A: Given data;  From the given figure, Three sets of parallel plates LM,NR and PQ.   View factor FU is…

Q: about the y a

A:

Q: Quest A A vel find + Solutic

A: GivenV→=axi^+byj^  where a=1and b=1

Q: Answqer b) only

A:

Q: tive and compression negative. 45°

A: Draw the free body diagram for the above problem as follows.

Q: 6) Spatter free operation is a key feature of Globular metal transfer Spray transfer Cold metal…

A: In spray transfer process no spattering, fusion is good, a smooth bead form, and it's weld…

Q: Describe what is Design for Assembly (DFA).

A:

Q: The suitable terms for the blanks in the statement ."To change from psig to psia , you must ass…

A: There are many different units of measuring pressure. We can use Pascal(Pa). atmospheric(atm), bar,…

Q: drawing all the views

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: mode shapes

A: mx¨+kx=F for free vibration F=0 mx¨+kx=0 mass matrix m=m000m000m=m100010001 stiffness matrix…

Q: ces of wear.

A: answer given in below attachment

Q: oining process. Select one:

A: True

Q: Fill in the blank using R-134a

A: Using property table and P-h chart of R-134a, the required properties are taken.

Q: ure B A <1 of 1

A: Introduction: Velocity is defined as the rate of change of an object's location with regard to a…

Q: esign the additional comp-

A: Required which design is used components in series and parallel

Q: Draw Front View and Top View of the following component

A: Solution:

Q: a) Engine displacement.

A: Solution shown below

Q: rd frame and dr.

A:

Q: Draw and label the P-V and T-S diagrams

A: Given data: The adiabatic index is, k=1.35. The initial pressure is, P1=101.325 kPa. The initial…

Q: What does a milky coloured ATF indicate

A: ATF in cars is stand for automatic transmission fluid. When a radiator fails, then the contaminated…

Q: teps of how to draw the BUSHING of an IV cannula using SOLIDWORKS

A: A bush, sometimes known as a shrub, is a common plant in both the garden and the wild. Many…

Q: how can you creat a section view for attached imaje including front side top

A: To create all three views (front view, side view, and top view) are possible only when the isometric…

Q: What i deep g a cons 80 rpm

A: Given data,Fr=2820NN=80deep groove ball bearing=6308SKF

Q: extracting IC

A:

Q: Orthographic view

A:

Q: f the desc oth of cut rations

A: Chip forming ;

Q: Qll Draw Hhe loop TF= Gcs) = %3D SCS+2)Cs+65+25) and Rind wax K forstability

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.