Ехample.5: A carrier wave is frequency modulated using a sinusoidal signal of frequency fm and amplitude Am. In a certain experiment conducted with fm-1 kHz and increasing Am, starting from zero, it is found that the carrier component of the FM wave is reduced to zero for the first time when Am=2 volts. What is the frequency modulation of the modulator? What is the value of Am for which the carrier component is reduced to zero for the second time?

Ехample.5: A carrier wave is frequency modulated using a sinusoidal signal of frequency fm and amplitude Am. In a certain experiment conducted with fm-1 kHz and increasing Am, starting from zero, it is found that the carrier component of the FM wave is reduced to zero for the first time when Am=2 volts. What is the frequency modulation of the modulator? What is the value of Am for which the carrier component is reduced to zero for the second time?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the frequency deviation and carrier swing for a frequency modulated signal which has aresting frequency of 105.000 MHz and whose upper frequency is 105.007 MHz when modulated bya particular wave. Find the lowest frequency reached by the FM wave.
(a) Determine the frequency deviation ∆f and the carrier swing for an FMsignal with a carrier frequency of 100 MHz and whose upper frequency swing is100.007 MHz when modulated by signal m(t).(b) Find the lowest frequency swing experienced by this FM signal.
The modulating signal that is the input into an FM modulator is m(t)=2cos(10??).a) Express the time domain expression of ?(?) signal.b) Express FM signal in terms of Bessel functions.c) Sketch the frequency spectrum of the modulated signal.d) Determine the bandwidth of ?(?) occupies 98% of the total power (Carson Rule) in the acquired spectrum.e) Determine the condition of required bandwidth of ideal BPF if at least 80% of the total power appears at the output of the filter?
A 162-MHz carrier is deviated by 12 kHz by a 2-kHz modulating signal. The maximum deviation of an FM carrier with a 2.5-kHz signal is 4 kHz. Compute the bandwidth occupied by the signal, by using the conventional method and Carson’s rule. Sketch the spectrum of each signal, showing all significant sidebands and their exact amplitude.
Sketch FM and PM waves for modulating segnals M(t) show in below figure. The constants Kf and kp are 2π ×10^5 and 10π respectively,and the carrier frequency is fc=100MHZ
Calculate the frequency deviation and the carrier swing of a frequency- modulated wave which was produced by modulating a 50.4 MHz carrier. The highest frequency reached by the FM wave is 50.415 MHz. Then calculate the lowest frequency reached by the FM wave. If the frequency of the modulating signal is 5 KHz, what is the bandwidth of the FM wave?
1. A 1500-kHz carrier and kHz intelligence signal are combined in a nonlin-ear device. List all the frequency components produced. *2. If a 1500-kHz radio wave is modulated by a 2-kHz sine-wave tone, what frequencies are contained in the modulated wave (the actual AM signal)? *3. If a carrier is amplitude-modulated, what causes the sideband frequencies? *4. What determines the bandwidth of emission for an AM transmission? *10. What are some of the possible results of overmodulation? *11. An unmodulated carrier is 300 V p-p. Calculate %m when its maximum p-p value reaches 400, 500, and 600 V. (33.3%, 66.7%, 100%) 12. If V and V as shown in Figure 8, determine %m. (53.85%) 13. Determine and from Problem 12. ( Vpk, Vpk)
-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
1. For a system with FM modulation, the amplitude of the unmodulated carrier is 12Vp, if the modulation index is 1.5 and the load resistance RL is 10 ohms,a) determine the power in the unmodulated carrier; b) Determine the power at the carrier frequency and at each significant side frequency for the modulated wave. What value of power do you obtain when adding the values obtained in question (b)?
For an Armstrong indirect FM transmitter with the crystal carrier oscillating at 210 kHz, the crystal reference oscillating at 10.2 MHz, the sideband voltage is 0.018 V, the carrier input voltage to the combiner is 5V, the first and second multipliers are both 40, and the modulating signal frequency is 2 kHz, determine: a.) modulation index at the output of the combining network and the power amplifier; b.) frequency deviation at the same two points; and c.) the transmit carrier frequency.
In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC