Engine Oil at 58.95 degrees celsius Flows over a 5m long flat plate whose temperature is 20.11 degrees celsius with a velocity of 2.2m/s. Determine the rate of heat transfer (W), considering forced convection, per unit width of the entire plate. Density = 876kg/m^3 Thermal conductivity = 0.144W/m-K Pr = 2870 dynamic viscosity = 0.21kg/m-s Q = ?

Engine Oil at 58.95 degrees celsius Flows over a 5m long flat plate whose temperature is 20.11 degrees celsius with a velocity of 2.2m/s. Determine the rate of heat transfer (W), considering forced convection, per unit width of the entire plate. Density = 876kg/m^3 Thermal conductivity = 0.144W/m-K Pr = 2870 dynamic viscosity = 0.21kg/m-s Q = ?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.7P: 5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is ....

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
Ethylene glycol at 40°C flows over a heated plate very wide, 6 m long, at velocity of 0.04 m/s. For a temperature = 90°C, determine: 1- the thickness of the hydrodynamic boundary layer at the end of the plate2- the thickness of the thermal boundary layer at the end of the plate3- the local and average heat transfer coefficient at the end of the plate4- the total heat flux transferred from the heated surface.
. Castor oil at 36 °C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surfacetemperature of 96 °C, determine (i) the thermal boundary layer thickness at the end of the plate,(ii) the local heat transfer coefficient at the end of the plate, and (iii) the rate of heat transfer fromthe entire plate
Water at 45.0oC flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long (in the flow direction), and its surface is maintained at a uniform temperature of 5.0oC. Calculate the steady rate of heat transfer per unit width of the plate. Properties The properties of air at 1 atm and the film temperature of (Ts+T∞)/2 = (5+45)/2 = 25°C are: ρ = 996.6 kg/m3, k = 0.610 W/m.oC, μ = 0.854x10-3 kg/m.s, Pr = 5.85
Mercury at 25°C flows over a 3-m-long and 2-m-wide flat plate maintained at 75°C with a velocity of 0.01 m/s. Determine the rate of heat transfer from the entire plate.
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
If forced convection uses Reynolds number to account for fluid movement during forced convection, what dimensionless number is used for natural convection?
a 6cm diameter shaft rotates at 3000rpm in a 20cm - long bearing with a uniform clearance of 0.2mm. At steady operating conditions, both the bearing and the shaft in the vicinity of the oil gap are at 50°c, and the viscosity and thermal conductivity of lubricating oil are 0.05N.s/m^2 and 0.17W/m. k. By simplifying and solving the continuity, momentum, and energy equations, determine: a) the maximum temperature of oil. b) the rate of heat transfer to the bearing and the shaft, and the mechanical power wassted by the viscous dissipation in the oil?
Q3: Air flows across a 20-cm-square plate with a velocity of $ m/s. Free-stream conditions are 10-C and 0.2 atm. A heater in the plate surface furnishes a constant heat-flux condition at the wall so that the average wall temperature is 100-C. Calculate the surface heat flux and the value of h at an x position of 10 cm. Answers: Q= 1414 W, b= 13.3 Wm?.C