Engine oil is heated by flowing through a circular tube of diameter D = 50 mm and length L = 25 m and whose surface is maintained at 150°C. (a) If the flow rate and inlet temperature of the oil are 0.5 kg/s and 20°C, what is the outlet temperature Tm,o? What is the total heat transfer rate q for the tube?

Engine oil is heated by flowing through a circular tube of diameter D = 50 mm and length L = 25 m and whose surface is maintained at 150°C. (a) If the flow rate and inlet temperature of the oil are 0.5 kg/s and 20°C, what is the outlet temperature Tm,o? What is the total heat transfer rate q for the tube?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.12P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Water at a flow rate of 0.215 kg/s is cooled from 70°C to 30°C by passing it through a thin-walled tube of diameter of 50 mm and maintaining a coolant at 15°C in cross flow over the tube. What is the required tube length if the coolant is air and its velocity is V = 20 m/s?Water : cp = 4181 J/kg⋅K, μ = 548 × 10-6 N⋅s/m2, k = 0.643 W/m⋅K, Pr = 3.56.Air : ν = 15.89 × 10-6 m2/s, k = 0.0263 W/m⋅K, Pr = 0.707.(Hint: For external flow use Churchill/Bernstein correlation.)
Air (pressure 1 atm) enters a circular pipe 5 cm in diameter at 20 °C with an average speed of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the mean outlet temperature is 80°C. Estimate the length of the tube. Mainly, I also need the solution from concepts of how the heat flow behaves in the system, it can be with a diagram.
Air (1 atm) enters into a 5-cm-diameter circular tube at 20°C with an average velocity of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the outlet mean temperature is 80°C. Estimate the length of the tube.
Water at a flow rate of 1kg/s is flowing in a pipe of internal diameter 5 cm. If the inside pipe surface temperature is 90°C and mean bulk water temperature is 50°C, compute the convective heat-transfer coefficient. Estimate the convective heat.
Engine oil flows through a 50 mm diameter tube at an average temperature of147°C. The flow velocity is 80 cm/s. Calculate the average heat transfer coefficient if the tube wall is maintained at a temperature of 200°C and it is 2 m long. Hint: Area can be assumed to be equal to the vertical projectiion of the tube , i.e. LD. Ans.: h = 377.36 W/m2.K . Draw an illustration. Note: use the formula on the picture
Water flows through a tube of 5mm inside diameter with a volumetric flow rate of 7.8 cm3/s. Wall temperature of the tube is kept constant at 80oC. In a fully developed velocity and temperature profile region of 5m length, calculate the bulk temperature of exiting water if its inlet temperature is 20oC
Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?
an oil at average temperature of 100 F flows at 1.2 ft/s velocity 0.834in inside diameter horizontal tube. The tube is heated by uniform heat flux the average surface temperature is 120F. Determine the heat transfer coefficient, Then the rate of heat transfer per length of the heating tube. Please write assumptions and do a sketch
Water at 10oC enters a tube of 0.1 m diameter at the mean flow velocity of 0.4 kg/s. Calculate the exit water temperature if the tube is 15 m long and the wall temperature is constant 30oC.
Example 4: Hot air at atmospheric pressure and 80°C enters an 8–m-long uninsulated square duct of cross section 0.2 m  0.2 m that passes through the attic of a house at a rate of 0.15 m3/s (Figure). The duct is observed to be nearly isothermal at 60°C. Determine the exit temperature of the air and the rate of heat loss from the duct to the attic space.