esign a muff coupling to connect shaft transmitting 40kw at 120rpm .the permissible shear and crushing stresses for the shaft and the key material are 30Mpa and 80Mpa respectively .the material for muff is cast iron with permissible shear stress is 15Mpa .assume that maximum torque transmitted is 25 percent greater than mean torque

esign a muff coupling to connect shaft transmitting 40kw at 120rpm .the permissible shear and crushing stresses for the shaft and the key material are 30Mpa and 80Mpa respectively .the material for muff is cast iron with permissible shear stress is 15Mpa .assume that maximum torque transmitted is 25 percent greater than mean torque

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

2. Design a muff coupling to connect two shafts transmitting 40 kW at 120 r.p.m. The permissible shear and crushing stress for the shaft and key material (mild steel) are 30 MPa and 80 MPa respectively. The material of muff is cast iron with permissible shear stress of 15 MPa. Assume that the maximum torque transmitted is 25 per cent greater than the mean torque
7. Design a muff coupling for joining shafts transmitting 8 kW at 400 rpm. The shaft and the key are made of steel with 45 MPa and 80 MPa allowable stresses in shear and crushing, respectively. The material of the sleeve is CI, with allowable shear stress 10 MPa. Service factor KS =1.2.
Design a muff coupling to connect two shafts transmitting 40 kW at 120 r.p.m. The permissibleshear and crushing stress for the shaft and key material (mild steel) are 30 MPa and 80 MParespectively. The material of muff is cast iron with permissible shear stress of 15 MPa. Assumethat the maximum torque transmitted is 25 per cent greater than the mean torque
A solid steel shaft 4.5 m long is stressed at 75 MPa when twisted through 4.5°. What power can be transmitted by the shaft at 25 Hz? Use G = 83 GPa.
A shaft ABC rotates at 500rpm and is driven through a coupling at the end A. At B a pulley takes off two-third of the power, the remainder being absorbed at C. The part AB is 1.5m long and of 100mm diameter, BC is 2m long and of 75mm diameter. The maximum shear stress set up in BC is 40MPa. Determine the maximum stress in AB and the power transmitted by it, and calculate the total angle of twist in the length AC. Take G = 80GPa.
A V-belt drive transmits 20kW from an electric motor running at 1440rpm to the main shaft of a roving machine. The motor and main shaft pulleys have 300 & 600 rpm respectively. The coefficient of friction between belt and pulley is 0.25. The centre distance between the shafts is 1000mm. The top width, thickness, section angle and density of belt and permissible tension on the belt are 22mm, 14mm and 40deg, 0.97gcm-2 and 600N respectively. How many belts are needed? Calculate the length of a belt needed
Write legibly, provide manual step by step solution, and diagram for below given problem. A hollow shaft that has 110mm outside diameter and 80mm inside diameter is used to transmit 120kw at 500rpm. Determine the shaft stress. Ans.12.18MPa.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the maximum shear stress in the shaft material?