For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of th shear stress at point a of the n-n section |t| Specify in MPa units. Take the P value of 57 kN and the D wwwww wwww value of 44 mm in the question.

For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of th shear stress at point a of the n-n section |t| Specify in MPa units. Take the P value of 57 kN and the D wwwww wwww value of 44 mm in the question.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FInd the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: w = 17 kN/m L = 8 m b = 85 mm h = 178 mm Ensure that your answers are in MPa.
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
What is the maximum normal stress, MPa, due to bending on section C? For S200x27.4, S = 235µm^3. Answer in whole numbers, no units. (Example: 123MPa --> 123)
Consider that the section is transmitting a positive bending moment about the z axis,Mz, where Mz=10 kip*in if the dimensions of the section are given in ips units, or Mz=1.13kN*m if the dimensions are in SI units. Determine the resulting stresses at the top and bottom surfaces and at every abrupt change in the cross section. Find the second moment of area, the location of the neutral axis, and the distances from the neutral axis to the top and bottom surfaces.
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
Help me determine Maximum shear stress
Determine the maximum bending stress (in Pa) for the beam shown belowif P = 1925 N, T = 4796 Nm, a = 0.96 m, b = 0.96 m, c = 0.69 m, w = 42 mm, and h = 77 mm . Round off the final answer to two decimal places.
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
A loaded beam, 60 mm wide by 100 mm high and 6 m long, has the shear and moment diagrams as shown below. Determine (a) the magnitude, type and location of the maximum flexural stress (in MPa) (b) the stress (specify the type) in a fiber 30 mm from the top of the beam at a section 3.5 m from the left end. I = bh3/12
PART 1 answer Ay=45kN Dy=140kn PART 2 Determine the shear force acting at each of the following locations: (a) x = 2m (b) x = 6m (c) x = 9m (d) x = 12m My Answer: (a) V= 45kN (b) V= -20kN (c) V= -110kN (d) V= 30kN PART 3 Determine the bending moment acting at each of the following locations: (a) x=4m (b) x = 8 m (c) x = 10 m When entering your answers, use the bending moment sign convention. Need Answers: (a) M= ________________kN-m (b) M= ________________kN-m (c) M= ________________kN-m