mechanical resistance For the circular cross section shown,the value of moment of Inertia (I) is:equal toD=6 in31 x 10^3 in^216x10^6 in^41017.87 in^463.61 in^4 OFor the circular cross section shown,the value C is from the neutral axiscenter of the circle to top point of* :the cross section, which is equal toD=6 in2 in3 in4 in6 in

Answered: Image /qna-images/answer/ab9fd101-77d4-437a-b346-c86a3dcbcaf3.jpg

Answered: For the circular cross section shown,…

Engineering

Mechanical Engineering

For the circular cross section shown, the value of moment of Inertia (I) is :equal to D=6 in 31 x 10^3 in^2 O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thank u Find the Moment of Inertia (based on Carbon, change the E-Glass to Carbon), I, for the section shown. Calculate by using the Face Sheets only, do not include the foam. Given: E-Glass, E = 3,000,000 psi; Carbon, E = 9,000,000 psi; Cross-Section of the sheet; w (width) = 24” T1 = 0.6”; T2 = 10”; T3 = 1.4” NA = ________ in Moment of Inertia, I =______________________ in4
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. The cross-sectional dimensions of the beam are also shown. a.Determine the centroid location (measured upward from the bottom), in mm rounded to the nearest tenths. b.Determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures. c. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. d. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures.
11) A cylindrical rod of constant radius andconstant shear modulus, G is of length Land located between z=0 and z=L.t=zsin(πZ/2L). call the polar moment of inertia J. The boundary conditions areΦ(0)=0 AND Φ(L)=0 Find Φ(z) and graph (1/GJ)*Φ(Z), and (1/GJ)*(dΦ/dz) ?
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
Q # 5: a. Discuss the importance of moment if inertia in linear and rotational motion.b. Engineer design machine parts, discuss the parameters.
A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa. Calculate the polar second moment of area of the shaft?
The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of Ix¯ = 654 in.4 by treating the section as being composed of three rectangles.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 16 mm d = 120 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1737 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 254790000 mm4. If the beam will be subjected to a shear force of V = 250 kN, determine the shear stress at point K, located at yK = 80 mm below the z centroidal axis.
A uniformly tapered tube AB with a hollowcircular cross section is shown in the figure. The tubehas constant wall thickness t and length L. The averagediameters at the ends are dA and dB = 2dA. The polarmoment of inertia may be represented by the approximateformula Ip ≈πd 3t/4
A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed that the shaft twists 1.5° in a length of 5 metres at 500 r.p.m. The shaft is solid and has a diameter of 200 mm. If the modulus of rigidity for the shaft material is 85 GPa, find the power transmitted by the turbine.
A machine part as shown in following figure consists of three disks linked by light weight struts. Use mA=0.62 kg, mB=0.98 kg, mC=0.2kg, a=0.78m, b=0.21m and c=0.807774721m. a. What is this body's moment of inertia in kg/m2 about an axis through the center of disk A, perpendicular to the plane of the diagram? Insert your answer correct up to at least a third decimal place. b. What is the moment of inertia in kg/m2 about an axis through the centers of disk B and C? Insert your answer correct up to at least a third decimal place. c. What is the body's kinetic energy in Joule if it rotates about the axis through A with angular speed ω=32 rad/s? Insert your answer correct up to at least a third decimal place.