Answered: For the two port network shown.…

For the two port network shown. Calculate the maximum .average load power Z11=162 9A 3142 Z12=-122 162 ms Z21=102 Z2=182 22 W O 20 W O 19 W O 21 W O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26MCQ: A balanced -load can be converted to an equivalent balanced-Y load by dividing the -load impedance...

See similar textbooks

Related questions

Q: Q3. The ABCD constants of a 3-phase, 345 kV transmission line are A = D = 0.98182 +j 0.0012447 B =…

A: A 3-ph transmission line ABCD parameters are, A = D = 0.98182 + j 0.0012447 B = 4.035 + j 58.947…

Q: Q3. The ABCD constants of a 3-phase, 345 kV transmission line are A = D = 0.98182 + j 0.0012447 B =…

Q: A three phase, 60 Hz, 60 km long transmission line has series impedance Z=0.1+ j0.5Q/ km delivers 10…

A: Given Frequency f = 60 Hz Line length l = 60 Km Impedance Z = 0.1+j0.5 ohm/km Load power SL = 10…

Q: Question 4.) An overhead, single-phase transmission line delivers 1.1MW at 33 kV at 0.8 p.f.…

A: According to question answer rule of Bartleby I have to solve first three sub part.

Q: Q2/ A single phase overhead transmission line delivers 1100 kW at 33 kV at 0•8 p.f. lagging. The…

Q: In three phase transmission line system with no transposition have the inductance matrix as shown…

Q: Q.30: For the two-port electric network shown in figure beside, calculate the maximum load power?…

A: Draw the circuit diagram again and show all the currents and the voltages,

Q: Zo VG No z = 0 z = d Given the transmission line above with: ZG = 252; Zo = 502; ZL = 75N Which of…

Q: Obtain the impedance diagram with all impedance including the load impedance marked in per unit for…

Q: EXAMPLE: A single phase overhead T.L delivers 1100 KW at 33 KV at 0.8 p.f lagging, the total…

Q: I need all steps answer A 3-phase overhead transmission line delivers a load of 80 MW at 0.8 pf…

Q: 4.21 A 138-kV, three-phase short transmission line has a per-phase impedance of (2 + j4) 2. If the…

A: As per our guidelines we have to solve 1st question if students posts multiple questions, so iam…

Q: For the two port network shown. Calculate the maximum average load power. Z11=3.752 0.5A Z12=-3.1252…

A: The source transformation is used to convert the practical current source into practical voltage…

Q: The bus admittance matrix of a power system is given as 1 1[-j 50 + j 10 2 +j 10 - j 30 +j 10 3 +j5…

Q: Q3. The ABCD constants of a 3-phase, 345 kV transmission line are A=D= 0.98182 +j 0.0012447 B= 4.035…

Q: S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 +…

Q: For the two port network shown. Calcula the maximum average load power. Z11=3.752 0.5A Z12=-3.1252…

Q: A single phase overhead transmission line from Muscat to Nizwa delivers 1800 KW at 22 KV at 0.8…

Q: EXAMPLE: A single phase overhead T.L delivers 1100 KW at 33 KV at 0.8 p.f lagging, the total…

Q: For the two port network shown. Calculate the maximum average load power. Z11=3.752 0.5A Z12=-3.1252…

A: The source transformation is used to convert the practical current source into practical voltage…

Q: Q3. The ABCD constants of a 3-phase, 345 kV transmission line are A = D = 0.98182 + j 0.0012447 B =…

A: In the given question, ABCD parameters A= D= 0.98182+j0.0012447 B= 4.035+j58.947 C= 0+0.0061137…

Q: 230 V, short-length transmission line has a line impedance of (1.04 + j4.89) Ω. The sending end…

Q: A 3-phase, 50 HZ, transmission line represented by I-model and having the following parameters, A=…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: A load of 1100 kW at 0.85 power factor lagging is received at the end of a 3-phase line 30 km long.…

A: In this question we wil find sending end voltage , sending end power factor, percentage regulation ,…

Q: a)Use Thevnin's theorem and maximum Dower transfer theorem to evaluate maximum avetoge power…

A: As per Bartleby guidelines we are allowed to solve only one question, since these parts are…

Q: A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor…

A: In the single phase overhead transmission line Delivered power 1MVA at 11kV at 0.86 PF Find the…

Q: Q3. The ABCD constants of a 3-phase, 345 kV transmission line are A = D = 0.98182 + j 0.0012447 B =…

Q: A 270 kV, three phase transmission line with a 430 km length. The series impedance Z =…

A: 270kV , 3 phase transmission line Series and admittance parameters are given. Find. The T and π…

Q: Calculate the impedance parameters for the two port network Verify the result by using both methods…

Q: A 60-Hz short transmission line, having R = 0.62 ohms per phase and L = 93.24 millihenrys per phase,…

A: First we will calculate receiving end load current and than sending end voltage sending end…

Q: VR An overhead 3-phase transmission line delivers 1200 kW at 22 kV at 0.8 power factor lagging. The…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A single-phase overhead transmission line delivers power of 1.6 MW at 132kV at 0.8 power factor…

Q: A short 3-phase transmission line connected to a 33kV, 50HZ generating station at the sending end is…

A: Given P=10 MW power factor (cos ϕr)=0.8 lagging Vs(line) =33 kV f=50 Hz Transmission efficiency =96…

Q: A 3 phase, overhead transmission line has a total series impedance per phase of 200 ohms and a total…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The bus impedance matrix for the 3-bus system is: 30.183 j0.078 j0.141 Z- 30.078 j0.148 0.106 j0.141…

A: In this question we need to find a new term of Z12 .

Q: The ABCD constants of a 3-phase transmission line are A = D = 0.8 Z1°; B = 170285° Q; C = 0.02Z90.4°…

A: Given values are - A=D=0.8∠1oB=170∠85oC=0.02∠90.4omhoSending end voltage VS=400kV

Q: (d) The ABCD constants of the three-phase transmission line of Figure Q2 are given below. A = D =…

A: In this question we need to find a voltage regulation of line .

Q: 2. A 3-phase transmission line, 160 km long, has the following constants : Resistance/phase/km…

A: The solution can be achieved as follows.

Q: A 130 kV, 50 Hz, 3-phase transmission line delivers a load of 58 MW at 0.88 p.f. lagging at the…

Q: For a three-phase long transmission line, Z, = 406.4/-5.48" 2, V = 215/0" kV und I = 335.7/0 A, all…

Q: The 3-phase transmission line parameters are given bellow. 1. Receiving end power 40 MW, 2.…

A: As per the guidelines of Bartleby we supposed to answer first three sub part of the question for…

Q: A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 7 0 and…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: An overhead 3-phase transmission line delivers 1200 kW at 22 kV at 0.8 power factor lagging. The…

A: In this question we need to find a sending end voltage , sending end power factor voltage…

Q: A 220 kV three-phase transmission line is 90 km long. The resistance is 0.1 92/km and the inductance…

A: Given- Three-phase transmission line, VR=220 kV,D=90 km,R=0.1 Ω/km,L=1 mH/km. To Find- (i) voltage…

Q: 1. Maximum power transfer happened when! a. Z₁1-Zg b. Z₁-Zh c. ZL-Z22. 2. The voltage equations in…

A: 1) Maximum power transfer happen when.... ANSWER - ( b ) ZL=Zth* in a DC circuit, the load…

Q: 1. A three phase, 60 Hz, 60 km long transmission line has series impedance Z=0.1+j0.5Q/ km delivers…

Q: A balanced 3-phase load of 30 MW is supplied at 144.3 kV and 0.85 pf lagging by means of…

A: The solution can be achieved as follows.

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

For the two port network
shown. Calculate the maximum
.average load power
Z11=162
9A
3142
Z12=-122
162
ms
Z21=102
Z2=182
22 W O
20 W O
19 W O
21 W O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0·2 Ω and inductive reactance is 0·4 Ω. Determine the voltage regulation if the load power factor is (i) 0·707 lagging (ii) 0·707 leading. [(i) 5·3% (ii) −1·65%]
A single phase transmission line is delivering 500 kVA load at 2 kV. Its resistance is 0·2 Ω and inductivereactance is 0·4 Ω. Determine the voltage regulation if the load power factor is (i) 0·707 lagging (ii)0·707 leading.
A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15 Hanni, capacitance between each phase and neutral 0.8uF. At the far end a load of 30 MW at 110 kV, 50 Hz frequency is connected at 0.8 power factor. So ( 1 ) sending end voltage ( 2 ) sending end current
For the adjacent circuit Vab=420V and the source part is balanced. Zan= j16Ω / Zbn= j24Ω / Zcn= -j24Ω According to the transmission lines ignoring their impedance Ib the value of the current with the angle calculate.
l. A single-phase distributor AB has a total impedance 0f (0.1+j0.2) ohms. At the far end B, a current of 80A at 0.8 pf lagging and at mid-point C a current of 100A at 0.6 pf lagging are tapped. If the voltage at B is maintained at 200V, determine the sending end voltage.
For a three-phase positive sequence ΔΔ-connected system, Vab=3.6∠56.0Vab=3.6∠56.0. Then VbnVbn is:
4.The sending end and receiving end voltages of a 3p transmission line at a 200MW load are equal. The maximum power transmitted per phase is 566.2 MW. The per phase line impedance is 1.7 Ohms. Calculate the sending end voltage. A. 23.79 B. 962.54 C. 31.02 D. 2.89
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
The ABCD constants of a 3-phase line are: A = D = 0.98182 + j0.0012447, B = 4.035 + j 58.947 and C = j0.00061137. If the sending end voltage is 387.025 kV L9.542o and the sending end current is 529.29 Amp L-27.325o. Find the receiving end voltage and current delivered to the load.
A short 3-4 transmission line with an impedance of (5 +j 20) O per phase has sending end and receiving end voltages of 46-85 kV and 33 kV respectively for some receiving end load at a p.f.of 0-8 lagging. Determine: (i) power output (ii) sending end power facto [(i) 22-86 kW (ii) 0-657 lag]
Find the total impedance of the network if Z1 = 10 + j5 ohm, Z2 = 10 - j5 ohm, Z3 = 10 ohms, and Z4 = j5 ohm are all connected in parallel.
In the YY Connection, the Phase Current and Line Current are normally equal, can you verify also can you find the Phase voltage for all the configurations