Gear B is rigidly attached to drum A and is supported by two small rollers at E and D. Gear B is in mesh with gear C which is subjected to a torque of M= 60 N.m. Determine the angular velocity of the drum A after C has rotated 5 revolutions, starting from rest. Gear B and the drum have a mass of 100 kg and a radius of gyration about their rotating axis of 250 mm. Gear C has a mass of 30 kg and the radius of gyration about its rotating axis of 125 mm. 300 mm 200 mm E 150 mm M B

Gear B is rigidly attached to drum A and is supported by two small rollers at E and D. Gear B is in mesh with gear C which is subjected to a torque of M= 60 N.m. Determine the angular velocity of the drum A after C has rotated 5 revolutions, starting from rest. Gear B and the drum have a mass of 100 kg and a radius of gyration about their rotating axis of 250 mm. Gear C has a mass of 30 kg and the radius of gyration about its rotating axis of 125 mm. 300 mm 200 mm E 150 mm M B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
The 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.
Gears A and B each have a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A torque M with constant magnitude of 10 N.m to gear C. Determine a) the number of revolutions of gear C that is required for its angular velocity to increase from 100 to 450 rpm. b) the corresponding tangential force acting on gear A Please include the free body diagram if necessary.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 32 kg and a radius of gyration k_O = 260 mm. The men A and B have a mass of 60 kg and 70 kg, respectively. Assume they do not move relative to the rope during the motion. Neglect the mass of the rope. If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man A in 4.2 s starting from rest. vA= ??? If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man B in 4.2 s starting from rest. vB= ???
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.
In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.
At the instant shown, the 200-lb bar rotates clockwise at 4 rad/s. The spring attached to its endalways remains vertical due to the roller guide at C. If the spring has an unstretched length of 2ft and a stiffness of k = 9 lb/ft, determine the angular velocity of the bar the instant it has rotated 39° clockwise.
The spool has a mass of 20 kg and a radius of gyration of kO = 160 mm If the 15-kg block A is released from rest, determine the velocity of the block when it descends 850 mm .
The 31-kg reel is mounted on the 16-kg cart. Part A: If the cable wrapped around the inner hub of the reel is subjected to a force of P=50N, determine the velocity of the cart when t = 4.2 s. The radius of gyration of the reel about its center of mass O is kO=250mm. Neglect the size of the small wheels. Part B: Determine the angular velocity of the reel when t = 4.2 s.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.