Given:The wheel has a motor which can apply amoment M=26 N•mThe wheel rolls without slipping andhas a radius r= 0.2 mv= 1.5 m/sF= 15N0= 30°FindMDetermine the power of the hub motorDetermine the efficiency of the motor if atotal of 375 W is applied.

Given data: - The moment applied by the motor is M = 26 N-m. The radius of the wheel is r = 0.2 m.…

Given: The wheel has a motor which can apply a moment M= 26 N•m The wheel rolls without slipping and has a radius r= 0.2 m v= 1.5 m/s F= 15N F 0= 30° Find M Determine the power of the hub motor Determine the efficiency of the motor if a 375 W is applied. total

Given: The wheel has a motor which can apply a moment M= 26 N•m The wheel rolls without slipping and has a radius r= 0.2 m v= 1.5 m/s F= 15N F 0= 30° Find M Determine the power of the hub motor Determine the efficiency of the motor if a 375 W is applied. total

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it rotates with revolution of 67.6 RPS. Maximum torsional stress equivalent to 50000 kPa.
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).
A 5 hp motor with a speed of 900 rpm is used to drive an industrial fan with a velocity of 5.72m/s. The center distance between the sprockets is 1.5 times the diameter of driven sprocket andis equal to 630 mm. Determine the length of chain in pitches. Use RC 40 chain and service factorof 1.3.
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
The engine of the helicopter is delivering 600 hp to the rotorshaft when the blade is rotating at 1200 rpm. Determine to thenearest 1/8 in the diameter of the shaft is the allowable shearstress is 10.5 ksi and the vibration limits the angle of twist ofthe shaft to 0.05 rad. The shaft is 2 ft long and made fromsteel.
= 1 ective diameter of 75 i clutch have an effe S i, e 10.34, The contact surfaces in a cone requing s - S ind the torque The semi-angle of the cone is 15°, The coefficient of. s Pee : produce slipping of the clutch if an axial force applied is 180 N. . . orn, This cluch is employed o connect an electric motor running “mf”r:f o /‘.’K'W:‘ tha Jopwleel which s iniially stationary: The lywheel ha a mass of o e sricres o 150 mm. Calculate the time required for the flywheel to attain full speed and als 8 lostin the slipping of the clutch,
The journal bearings at A and B exert only x and z components of force on the shaft. Determine the shaft’s diameter to the nearest millimeter so that it can resist the loadings. Use the maximum distortion energy theory of failure with sallow = 200 MPa.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
The ball bearings are to be selected for an application in which the radial load is 2000N during 90 per cent of the time and 8000 N during the remaining 10 per cent. The shaft is to rotate at 150 r.p.m. Determine the minimum value of the basic dynamic load rating for 5000 hours of operation with not more than 10 per cent failures.
Q.(a)Derive the tension ratio of the belt drive. (b) Define the slip and show the effect of slip on velocity ratio
A steel shaft 100mm in diameter is loaded and support in shaft bearing 0.4m apart. The shaft carries three loads: first mass 12kg at the centre, second mass 10kg at a distance 0.12m from the left bearing and third mass of 7kg at a distance 0.09m from the right bearing. Find the value of the critical speed by using Dunker ley’s method if E = 2X1011N/m2.
A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock conditions where Ks= 1.25, and a factor of safety equal to or greater than 1.1 is appropriate. The pulley rotational axesare parallel and in the horizontal plane. The shafts are 8 ft apart. The 6-in driving pulley rotates at1750 rev/min in such a way that the loose side is on top. The driven pulley is 18 in in diameter. Thecoefficient of friction is 0.8. Analyze the centrifugal tension Fc and the torque T.?