A=2 Given Vs= (a+2) V, V, = 0.6 V. Check whether the diode D conductsor not and find the voltage at 2 N. Assume offset diode Model.I-2(a + 1)NII-Given Vs= (a+2) V. Plot the loadline equation.Find the range of Vs for whichthe diode D first conducts.III-Vs20100VLAssume ideal diode model.Fig. 1ww

Answered: Image /qna-images/answer/03c0b592-380c-47df-84e0-6dbc33b1ba74.jpg

Given Vs= (a+2) V, V, = 0.6 V. Check whether the diode D conducts or not and find the voltage at 20. Assume offset diode Model. I- %3D 2(a + 1)N D Given Vs= (a+2) V. Plot the load line equation. II- ww 102 Find the range of Vs for which the diode D first conducts. III- Vs 20 VL Assume ideal diode model. Fig. 1 ww ww

Given Vs= (a+2) V, V, = 0.6 V. Check whether the diode D conducts or not and find the voltage at 20. Assume offset diode Model. I- %3D 2(a + 1)N D Given Vs= (a+2) V. Plot the load line equation. II- ww 102 Find the range of Vs for which the diode D first conducts. III- Vs 20 VL Assume ideal diode model. Fig. 1 ww ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This problem concerns the following three samples of silicon, each of which has a different doping level: sample a : 6.25×10^15" cm" arsenic sample b: 10^16 cm boron, 5x10^15 cm phosphorous sample c : intrinsic (no doping) Complete the table like that shown below for these three samples. Assume that at room temperature the electron mobility He is 1600 cm /.s, the hole mobility H, is 600 cm2/V.s, and the intrinsic carrier concentration n, is (1/352) x10^10 cm.a- Find the resistivity in (Ω.cm) of sample a. b- Find the conductivity in (Ω.cm)-1 of sample bc- find the resistivity in (Ω.cm) of sample c.
The high-voltage power supply for a television's picture tube has an open-circuit voltage of 18 kV and an internal resistance of 1.5 MQ. (a) Find the voltage at the anode of the picture tube when the anode current is 800 µA. (b) What will the anode voltage be if the anode current is increased by 50%? (c) Find the short-circuit current of the power supply
1. Given the circuit below. Answer the following: A. Which diodes turned ON? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω. B. What is the current (in mA) in the circuit? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω. C. What is the voltage (in V) across the 100 Ω resistor? The diodes are made up of Silicon and the diode internal resistance rD is 1 Ω.
For the circuit given in Fig. 2, D1 is a diode, V1=5V, R1=1kΩ ,and RPot=1kΩ find the voltage VD and current ID.
Sketch the output waveform for the clipping circuit of Fig.1, if a load resistance RL of value1 kΩ is connected at the output terminals in parallel with the diode.
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
Determine the n-type doping concentration to meet the following specifications for a Si p–n junction:NA=1018 cm–3, Emax = 4 × 105 V/cm at VR = 30 V, T = 300 K. Please answer in typing format please
When a positive bias of 0.5 V is applied to the metal side of a Pt–Si junction, the junction has the capacitance of 0.25 pF. A bias of 1.5 V results in a capacitance of 0.05 pF. The junction area A = 10-5 cm2, and the temperature T = 300 K. The effective electron mass in Si is me* = 0.26 me. (a) Is the semiconductor of p- or n-type? What is the smallest value of the applied voltage at which the space-charge region in the semiconductor starts to appear? Is the metal work function bigger or smaller than the semiconductor’s? (b) What is the doping level of the semiconductor? (c) What is the value of the metal work function?
In the given system; Va, Vb, Vc effective value is 220V, Ly=300 mH and Ry=22 Ohms.It was observed that the yuk current is continuous when the tristorier is triggered for alpha=65 degrees; and D1the average value of the diode current was calculated as ID1 avg = 1.703A.Accordingly, calculate the average value of the current flowing through T3. IT3_ avg=?
A sample of silicon have electron concentration 3.2x10^11 m^-3 and L=86 mm, t=10 mm and w=35 mm, when sample is tested by Hall effect, the value of resistance 2.7 K ohm and the Hall coefficient=3.6 m^3/c, is obtained. 1. Which kind of semiconductor that the sample? 2. Determine the value of mobility for the sample in (1).
consider a silicon pn junction of doping concentrations of 5*10^16 cm-3 and 2*10^15 cm-3 at the p-side and n-side respectively if the pn-junction is forward biased y a voltage V=0.5 V considering a steady state. i) solve the continuity equation in the p side to find the electron concentration as a function of distance x . ii) find the electron current density Jn in the p-side at a distance 10 nm from the edge of the depletion layer.
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?