For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Use ideal model. *Use 4 decimal places. Assume r'a (for both diodes)=202. Note D, is Germanium, D2 is Silicon, VBIAS = 22V and RLIMIT = 2 kohms. VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 V ... Capture3.JPG +VD1- +VRLIMIT- +Voz- VBIAS

For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Use ideal model. *Use 4 decimal places. Assume r'a (for both diodes)=202. Note D, is Germanium, D2 is Silicon, VBIAS = 22V and RLIMIT = 2 kohms. VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 V ... Capture3.JPG +VD1- +VRLIMIT- +Voz- VBIAS

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is CEMF?
How many valence electrons are generally contained in materials used for insulators?
What is the difference between a diode and rectifier?
Can you answer the question by explaining step by step and explaining why you used that formula or calculations in details please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
Design the network of below to maintain V L at 12 V for a load variation (I L) from 0 mA to 200 mA. That is, determine R S and V Z. Determine P Z max for the Zener diode of part (a).
Consider the circuit below,assuming the diode is ideal:1) When voltage source (Vin) provides a positive voltage, the diode isequivalent to ____________ circuit2) When voltage source (Vin) provides a negative voltage, the diode isequivalent to ____________ circuit3) Sketch the I-V characteristic of the ideal diode model on the chart below.
For the half-wave rectifier circuit shown, the diode is not ideal and is modeled as an ideal voltage source of value Vf= 0.65V in series with an ideal diode. Vin= 5sin(2π100t) and R =510Ω. What is the output voltage at time t=24mst=24ms? 2- For the same circuit as in Question 1, what is the output voltage at time t=35.4ms t=35.4ms? Enter your answer in volts 3- For the same circuit as in Question 1, what is the magnitude of the diode current at time t=12mst=12ms? Enter your answer in mA without units.
Diodes D1, D2, D3 and D4 are identical Silicon diodes with forward voltage drop of 0.7volts. Consider vi to be the circuit's input voltage.A) Under what input conditions will diode D1 conduct? B) If D1 is conducting, express vo in terms of vi. C) Under what conditions will diode D4 conduct? D) If D4 is conducting, express vo in terms of vi. E) Under what input conditions will none of the diodes be conducting? F) If none of the diodes are conducting, what is vo? G) The input to the circuit has the waveform shown below. Plot the waveform of thevoltage vo. Show all the important quantities in your plot.
a. Determine VL, IL, and IR for the network of below if RL=180 ohms b. Repeat part (a) if RL=470 ohms c. Determine the value of RL that will establish maximum power condition for the Zener diode. d. Determine the minimum value of RL to ensure that the Zener diode is the the "on" state.