h G bị Q4) For the given system; a) Draw internal force diagrams and determine the most critical section. b) Show the stress distribution on this critical section and find the maximum normal stress. GIVEN: (1 = 50 cm, lz= 30 cm, M, = 5000 Nem, q, = 20 N/cm, bị = 4 cm, b2 = 2 cm, h = 4 cm, t = 1 cm

h G bị Q4) For the given system; a) Draw internal force diagrams and determine the most critical section. b) Show the stress distribution on this critical section and find the maximum normal stress. GIVEN: (1 = 50 cm, lz= 30 cm, M, = 5000 Nem, q, = 20 N/cm, bị = 4 cm, b2 = 2 cm, h = 4 cm, t = 1 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

From 3 forces, 2 bending moments and 1 toque acting on B, which ones are non zero, and the direction they are acting. Then indicate if they make shear or normal stress Draw 3-d stress state cust above plane a
A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the diagram below Determine all three principle stresses, the average normal stress, the max in plane shear stress, and the absolute max shear stress
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.
How can we find the maximum normal and maximum shear stress at the point?
Find the stresses in each direction, also find the change in volume of the block of dimension 120 mm x 60 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (tensile), 13 kN (compressive) respectively, Take E as 180 GPa, Poisson's ratio as 0.3. The stress along length direction (Unit in kN/m2)= _____________ The stress along width direction (Unit in kN/m2)= _____________ The compressive stress along depth direction (Unit in kN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
Please answer the problem completely. Show a free body diagram. Final answer: Shear stress = 3.2 mpa
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
For the two-dimensional stress fi eld shown in Fig. it isfound thatσxx = 3000 lbf/ft2 σyy = 2000 lbf/ft2σxy = 500 lbf/ft2Find the shear and normal stresses (in lbf/ft 2 ) acting onplane AA cutting through the element at a 30° angle asshown.