H.W.1/: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Fig. below. Determine the gage pressure of air in the tank if hl = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000 kg/m², 850 kg/m³, and 13600 kg/m3, respectively? Oil Air Water T ha Mercury

H.W.1/: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Fig. below. Determine the gage pressure of air in the tank if hl = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000 kg/m², 850 kg/m³, and 13600 kg/m3, respectively? Oil Air Water T ha Mercury

Name: H.W.1/: The water in a tank is pressurized by air, and the pressure i
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: H.W.1/: The water in a tank is pressurized by air, and the pressure is measured by amultifluid manometer as shown in Fig. below. Determine the gage pressure of air inthe tank if hl = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oi

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 14RQ: Atmospheric pressure at sea level under standard conditions is ______inches of mercury (Hg) or_____...

See similar textbooks

Similar questions

Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.
Any pressure reading can be expressed as a length or head,h = p / ρ g . What is standard sea-level pressure expressed in( a ) ft of glycerin, ( b ) inHg, ( c ) m of water, and ( d ) mm ofethanol? Assume all fl uids are at 20 ° C.
Q1 Determine the minimum size of glass tubing that can be used to measure water level, if the capillary rise in the tube is not to exceed 0.3 mm. Take surface tension of water in contact with air as 0.0735 N/m. A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. Q2) The tube is held vertical and partially filled liquid of surface tension 0.06 N/m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the density the liquid. Q10) In measuring the unit energy of a mineral oil (specific gravity = 0.85) by the bubble method, a tube having an internal diameter of 1.5 mm is immersed to depth of 12.5 mm in oil. Air is forced through the tube forming a bubble at the lower end. What magnitude of the unit surface energy will be indicated by a maximum bubble pressure intensity of 150 N/m.
what should be the gauge pressure and (b)the absolute pressure of water at depth 12m below the surface ? p water 1000kg/m3
pressurea are sometimes determined by measuring the height of a column of liquid in a vertical tube, what diameter clean glass tubing is required so that the rise of the water at 20°C in a tube due to capillary action (as opposed to pressure in tube) is less than h=1.0mm
Assuming specific weight of air to be constant at 12 N/m3, what is the approximate height of Mount Banahaw if a mercury barometer at the base of the mountain reads 654 mm and at the same instant, another barometer at the top of the mountain reads 480mm.
It is noted that while stopping, the water surface in a glass of water sitting in a cup holder of a car is slanted at angle of 25 degree relative to the horizontal sheet. Determine which the car is deccelerating in ft/s^2 Show complete sol’n pls
Oil (SG = 0.92) fills both pipe "A" and pipe "B" which are vertically separated by 24-inches. The two pipes are connected by a mercury (SG=13.6) manometer showing a 12-inch pressure differential. What are the specific weight, density, and specific volume of the oil? What is the difference in pressure between Pipe "A" and Pipe "B" (in psi)?
3. If the barometer reads 735 mmHg, determine what absolute pressure ,in bars,is equivalent to a vacuum of 280mmHg within a system.Neglect the effect of temperature and density of mercury.
In Fig., pressure gage A reads 1.5 kPa (gage).The fluids are at 20 ° C. Determine the elevations z , inmeters, of the liquid levels in the open piezometertubes B and C .
Q8: A gasoline line is connected to a pressure gage through a double-U manometer, as shown in Fig. If the reading of the pressure gage is 370 kPa, determine the gage pressure of the gasoline line.
The pressure of water in a pipeline was measured by means of a simple manometer containing mercury. The mercury level in the open tube is 160 mm higher than that of the left tube. The height of water in the left tube is 36mm. Determine the static pressure in the pipe in a).kN/m2. b) Head of water in meters,