has a double- The gear puller shown in Fig. threaded square-threaded screw with a mean radius of in., a pitch of 0.1 in., and a coefficient of friction of 0.30. The gear is wedged onto its shaft and requires a force of 100 Ib to remove it. Determine the moment that must be applied to the gear puller screw to remove the gear.

has a double- The gear puller shown in Fig. threaded square-threaded screw with a mean radius of in., a pitch of 0.1 in., and a coefficient of friction of 0.30. The gear is wedged onto its shaft and requires a force of 100 Ib to remove it. Determine the moment that must be applied to the gear puller screw to remove the gear.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
Design a turnbuckle subjected to a load of 50 kN with permissiblestresses are in 166.67 Mpa in tension , 83.33MPa in shear and 166.67 MPa incrushing.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
(6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head; the head is guided by linear slides with anti-friction bearings, and thus no appreciable friction is involved. If the coefficient of friction for the threads is 0.1, find: (a) the load that can be raised if the screw has 2 threads/in and an outside diameter of 2½in; (b) if a 4000-lb load is to be lowered, what torque must the screw transmit? (c) if the power screw of rotates 10 rpm, what is the linear speed of the driven head in feet per minute?
A plank 25 meters long is placed on rough inclined planes at an angle of 15 ̊ with the horizontalas shown in Figure 3. The angle of friction is ∅ = 15° at both inclines. If the weight of the plank is W= 350 N concentrated at 12 meters from end A, compute the minimum distance x from B at which aload P = 75 N can be placed before slipping impends.
Steel frame with thickness of 10mm, width 80mm and inner diameter of 1500.0mm being heated and shrinkable on steel wheel diameter 1500.5mm. If the coefficient of static friction is 0.30, what is the torque required to roll the tire with respect to the wheel? Neglecting the deformation of the wheel. Use E = 200 GPa.
3. A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of friction for the nut and bolt is 0.1 and for the nut and bearing surfaces 0.16, find the force required at the end of a spanner 0.5 m long when the load on the bolt is 10 kN.
A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A (on the ground). The angle of friction at all contact surfaces is 21.8°. Find the smallest angle 0 at which the ladder can be inclined with the horizontal before it is on its verge of slipping.
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular distributed load is being applied to the handle. With a coefficient of friction of 0.9, determine the smallest distributed load P necessary to resist an 85 N-m moment M.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is raised against a load of 10 kN by means of a hand wheel, the boss of which is threaded to act as a nut. A thrust collar, taking up the axial load,supports the wheel boss and has a mean diameter of 60mm. The coefficient of friction is 0.18for the screw and 0.16for the collar. If the tangential force applied by each hand to the wheel is 200 N, find suitable diameter of the hand wheel.