HW 10 An integral cycle circuit with source voltage Vs = 100 sin(wt) and resistive load 100, if the load has been connected for 10 cycles and disconnected for 5 cycles, Find: Average voltage and current. • Power delivered to load. Input volt-Ampere. • Power factor. Thyristor average current. Thyristor effective current.

HW 10 An integral cycle circuit with source voltage Vs = 100 sin(wt) and resistive load 100, if the load has been connected for 10 cycles and disconnected for 5 cycles, Find: Average voltage and current. • Power delivered to load. Input volt-Ampere. • Power factor. Thyristor average current. Thyristor effective current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
A single phase circuit with a given load 3 ohm resistance and inductive reactance of 4 ohms as well. The voltage is being supplied 220 Volts with a reference angle of 30 degrees at 60 Hertz frequency. Solve for P,Q, S. and power factor.
25kVA SINGLE PHASE VHAS POWER FACTOR .8 LAGGING , 10kVAR CAPACITOR CONNECTED FOR POWER FACTOR CORRECTION . CALCULATE INPUT TAKEN FROM THE MAINS IN KVA AND THE POWER FACTOR SKETCH PHASOR DIAGRAM WHEN MOTOR IS HALF LOAD AND FULL LOAD
A 25 kVA, 240 V single phase source supply the rated power at the rated voltage to a motor at 0.8 power factor lagging. Find the capacitor bank in order to improve the power factor to 0.9 lagging connected to a motor.a. Calculate the real power, reactive power and current before capacitor bank is connected? b. Calculate the power and reactive power after capacitor bank is connected? c.What is kVA rating of capacitor bank QC?
The total power drawn by the two-impedance load in parallel is 27kW at 0.90 power factor lagging, it's being supplied by a 230-volts AC source. One of the loads (Load 1) takes 19kVA at 0.81 power factor leading. What is the power factor of the unknown impedance (Load 2). The answer is 0.9864. Show the solution pls. Thank you!
Please answer all subparts for like either dislike is ready at least 5 subparts... A 3-phase, 450 V, 2-pole, 50 Hz, wye-connected, synchronous alternator. Xs = 1.62 ohm/phase. Connected to an infinite bus and supplies 120 kW with a power angle of 35 degrees.Neglect losses and find:a. turbine torque supplied to alternator.b. excitation voltage.c. active, reactive power and machine power factor.d. neglecting saturation effects of the field, the excitation voltagee. if the field current is reduced to 80% of its original value in part a.f. the turbine speed for 60 Hz operation.
A residential four-wire system supplies power at 220 V rms to the following single-phase appliances: On the first phase, there are ten 60-W bulbs. On the second phase, there is a 1-kW vacuum cleaner with a power factor of 0.9. On the third phase, there are ten 23-W compact fluorescent lamps with power factor of 0.61. Find a. The current in the neutral wire. b. The real, reactive, and apparent power for each phase.
Two 300kVA, 1000V, 50Hz alternators operating in parallel to supply a load of 500KW at UPF. 60% of the load is supplied by the first generator. If the terminal voltage and power supplied are kept constant always, then changing the excitation to make pf=0.8 lagging. Find the generator currents, power factors and total load current. (the generator and load are single phase)
Suppose an AC generator with V(t) = (150V)sin(100t) is connected to a series LRC circuit with R=40 Ohm, L=80 mH, and C=50 microFarad, as shown in figure. Calculate the maximum voltage across the resistor (VR0)?
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?