HW10 In an engine governor of the Porter type, the upper and lower arms are 230 mm and 330 mm respectively and pivoted on the axis of rotation. The mass of the central load is 13 kg, the mass of each ball is 1.5 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 40° and 55°, find, taking friction into account, the range of speed of the governor and Sensitiveness of Governors.

HW10 In an engine governor of the Porter type, the upper and lower arms are 230 mm and 330 mm respectively and pivoted on the axis of rotation. The mass of the central load is 13 kg, the mass of each ball is 1.5 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 40° and 55°, find, taking friction into account, the range of speed of the governor and Sensitiveness of Governors.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The belt drive in which pulleys rotate in the same direction is used to transfer power. The pulley diameters are 1.74m and 0.833m and it connects two parallel shafts which are 3.25m apart. The initial tension in the belt when it is stationary is 4500N. The smaller pulley is rotating at 710 rpm and coefficient of friction between the belt and pulley is 0.29. Determine the power transmitted by the belt drive
Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at 500 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 13.5o and a maximum mean diameter of 300 mm. The coefficient of friction is 0.25. The normal pressure on the clutch face is not to exceed 0.1 N/mm2
A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a speed of 10 meters per minute. The screw has a pitch diameter of 36 mm. The coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20% of the total torque input. Determine the motor power required to operate the screw.
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A motor vehicle of mass 1000 kg has road wheels of 600 mm rolling diameter. The total moment ofinertia of all four road wheels together with the half shafts is 10 kgm2, while that of the engine andclutch is 1 kg-m2. The engine torque is 150 N-m, the transmission efficiency is 90 per cent and thetractive resistance is constant at 500 N. Determine 1. Gear ratio between the engine and the roadwheels to give maximum acceleration on an upgrade of 1 in 20, and 2. The value of this maximumacceleration.
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
1. A triple-thread Acme-form power screw of 50 mm major diameter is used. The nut makes 1.5 turn per cm of axial travel. A force of 600 N is applied at the end of a 850 mm wrench used on the nut. The mean diameter of the collar is 90 mm. If the coefficient of friction at the thread and at the collar are 0.15 and 0.13, respectively. Determine the weight that is being lifted.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.