I = Using the 'single phase equivalent circuit' given below, the required parameters ir terms of motor parameters equations will be deducted. Equations separately for asynchronous motor powered by voltage source will be removed and the spaces given below will be written. V1 and 11 are the RMS value of the AC phase voltage and current. All formulas (3phase motor) will be written as a function of motor parameters and slip. Stator current Rotor current I2 = Pm = Shaft power Moment Tm = jx1 jx2 = V, 12 Yield jxm Thevenin emp. Zeh = Thevenin voltage Vth = T- Equivalent circuit

I = Using the 'single phase equivalent circuit' given below, the required parameters ir terms of motor parameters equations will be deducted. Equations separately for asynchronous motor powered by voltage source will be removed and the spaces given below will be written. V1 and 11 are the RMS value of the AC phase voltage and current. All formulas (3phase motor) will be written as a function of motor parameters and slip. Stator current Rotor current I2 = Pm = Shaft power Moment Tm = jx1 jx2 = V, 12 Yield jxm Thevenin emp. Zeh = Thevenin voltage Vth = T- Equivalent circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. A 6 pole wave wound shunt generator delivers 200A at a terminal voltage of 240V. Ra and Rsh are 0.03Ω and 70Ω respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current ? current per parallel path ? generated voltage ? Power developed ?
4. A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder resistance of 0.10 ohm. Armature, shunt field resistance and series field resistance are 0.10 ohm, 52.5 ohms and 0.10 ohm, respectively. If the core, friction, and windage losses amount to 631 watts, determine (a) HP of driving engine (b) commercial, electrical and mechanical efficiencies.
A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
Q. A 3-phase, star connected, 10 kVA, 400 V, salient pole alternator with direct and quadrature axis reactances of 15 ohm and 8 ohm respectively, delivers full-load current at 0.8 power factor lagging.Neglect the armature resistance. Solve this question to chose the correct answer for the following: The direct axis and quadrature axis components of armature current are ........ and ......... respectively ?
If the armature resistance of a 3-phase, 318.75 kVA, 2300-V synchronous generator is 0.35 ohms per phase, the synchronous reactance is It is 1.2 ohms. Calculate the excitation voltage and voltage regulation for the following load cases: a) Full load, back power factor of 0.8 and rated voltage. b) Full load, forward power factor of 0.6 and rated voltage.
1-) Total Armature Winding resistance of 200kW, 380V self-excitation shunt generator is 0.07 Ω and areawinding resistance is 60Ω. Brush-contact voltage drop is neglected. Generator 380V ratedit feeds the load at Rated Power value at voltage. (a) draw the equivalent circuit of the corresponding DC machine, specifying all current, voltage and winding resistors.Make appropriate arrangements for the generator (b) find the voltage value induced at full load (c) calculate the power value generated on the DC machine (Enter the formulas that you use for calculations and enter the names of the corresponding parameters.)
A 3 phase 4MVA, 12 kV star connected synchronous generator has Zs= 0.8+J30 ohm. Using circle diagram only, find: 1. The output power developed at unity power factor with excitation equal to 1.25 of rated voltage. 2. The load angle and power factor if the generator supplies (1500 KW) at rated voltage and excitation lequal to (1.2) of rated voltage. 3. Repeat part (2) when .armature resistance is neglected
Q. A 3-phase, star connected, 10 kVA, 400 V, salient pole alternator with direct and quadrature axis reactances of 15 ohm and 8 ohm respectively, delivers full-load current at 0.8 power factor lagging.Neglect the armature resistance. Solve this question to chose the correct answer for the following: The load angle?
Open circuit tests carried out on a 3.5 MVA, 4.16 kV, 60 Hz, three phase star connected synchronous generator gave the following results:If (A):1015202530EL (kV):3.54.165.76.257.95In the short circuit test a field current of 20A was needed to circulate full load current. The armature winding resistance is 1.2Ω /phase, the field winding resistance is 500 Ω and the rotational loss is 250kW. Determine the power angle, the voltage regulation and the efficiency when the generator delivers rated load at terminal voltage of 4.4 kV and at 0.8 power factor leading.Draw the power flow diagram for the generator and include all values of power flows.
Two D.C shunt generations running in parallel supply s total load current of125 A. The shunt field and armature resistances of each machine are 50 ohms and0.4 ohm respectively. The e.m.f.s. of the two generators at no load are 260 Vand 250 V respectively. Determine:(i) Current supplied by each generator: and(ii) The bus bar voltage.
The synchronous reactance per phase of the 460 V, 60 Hz, Y-connected 6-pole synchronous generator is 1.2 Ω. full load armature current 30 A (at 0.8 reverse power-coefficient). Rotary losses 1.5 kW and core losses 1.0 kW (60 Hz at full load). The armature resistance winding losses are neglected. Excitation current, generator no load terminal voltage is set to 480 V while operating. According to this: c. What is the efficiency of the generator when operating at rated current and a reverse power-coefficient of 0.8? D. How much shaft torque should be applied by the drive machine when the generator is running at full load? E. What happens to the induced torque?
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible