Identification Complete each statement. Write your answer at the end of each question. 92. To determine the gram-milliequivalent weight, molecular weight of the analyte is divided by 93. It is carried out by dissolving the substance under examination in an accurately measured quantity of standard solution known to be in excess and tittrating the excess of the latter with another standard solution. 94. This method of standardization is accomplished by making use of a standard solution. A

Identification Complete each statement. Write your answer at the end of each question. 92. To determine the gram-milliequivalent weight, molecular weight of the analyte is divided by 93. It is carried out by dissolving the substance under examination in an accurately measured quantity of standard solution known to be in excess and tittrating the excess of the latter with another standard solution. 94. This method of standardization is accomplished by making use of a standard solution. A

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter7: Extraction

Section: Chapter Questions

Problem 1Q

See similar textbooks

Similar questions

B. Determining the Composition of a Mixture of Sodium Chloride and Sodium Nitrate Partner I Prepare a solution of sodium chloride + sodium nitrate and indicator. Obtain a dropper bottle of potassium chromate (indicator) solution. To a clean and dry 125 mL Erlenmeyer flask, add about 40 mL of water and 8 drops of indicator solution. Weigh out approximately 0.05 grams of sodium chloride + sodium nitrate solid and record its exact mass. Dissolve the solid in the solution from step 1, stirring with a stirring rod to ensure complete dissolution. Determine and record the total mass of the Erlenmeyer flask and solution, noting the balance that you use to weigh. Rather than measuring the volume of silver nitrate solution added as in Part A, we will measure the mass of titrant added and make use of the weight-percentage concentration of silver nitrate in calculations. Prepare the silver nitrate solution. Obtain about 15 mL of 1.70% w/w silver nitrate solution in a 50 mL beaker. Designate a…
Calculate the mass percent of the ascorbic acid in the same show full solution Situation: The pounded Vitamin C tablet was half into two below are the calculated data in the experiment. Each of the half are transfered in a 250ml erlen meyer flask and added 75ml of deionized water for the vitamin C to dissolve. Then it was prepared for titration where the burette was filled with 0.09794M standardize NaOH solution then a total of with 3 drops 2% phenolphthalein indicator was added to each erlen meyer flask l, swrill it and begin the titration. below are the following data gathered: Vitamins used: Nature Made vitamin C 500mg tablet Trial 1 Mass: 0.3108g of Vitamin C tablet Initial volume: 1.6mL Final volume: 15.4mL Trial 2 Mass: 0.3349g Initial volume: 15.4 mL Final volume: 30.2 mL
If you choose a serial dilution—what would you do? Assume that you begin with a 1.0 M solution. You perform a 50% serial dilution to prepare four additional standards. What are the final concentrations of these new standards? Show a sample calculation.
Please determine how to make a working standard Solution of about 0.010mg/mL. Caffeine will be the active. Diluent will be water.
A 2.0 g of MgCO3 was dissolved and diluted to exactly 500-mL volumetric flask. If 50-mL aliquot was used in the analysis, what is the weight of MgCO3 present in the aliquot sample
From a 10-mL sample, a 1-mL aliquot was taken and diluted to 100mL. From this, a 5-mL aliquot was taken and diluted to 20mL.The final 20mL was found to have a concentration of 0.004M analyte X.What is the concentration of analyte X in the 10-mL sample?
PLEASE USE ANOTHER SOLUTION. WRITE ALL THE PROCESS. What is the minimum distribution constant that permits removal of 99% of a solute from 50.0 mL of water with five 10.0-mL extractions with toluene?
Prepare 100.00 mL of a solution with ALL the following chemicals into together; CHEMICALS PROVIDED solid FeCl3 6H2O, iron(II) chloride hexahydrate (source of FeCl3) dilute hydrochloric acid in the rack – 3.0 M solid sodium salicylate – 99.7% assay Concentrations needed in the 100mL solution FeCl3: 0.020 M HCl: 0.050 M Salicylate (mg/L): 40.25 PLEASE SHOW HOW TO CALUATE AND WORK. The only equations you will need to use are the equations for molarity and dilutions.
The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask and add deionized H2O to a final volume of 250.0 mL. Molar mass of H2C2O4•2H2O = 126.07 g/mol Mass of H2C2O4•2H2O = 1.5232g what is the Number of moles of H2C2O4•2H2O?
The stock erythrosine B solution is 8.5 × 10-5 M. Calculate the volume of this solution that you must pipet into a 50-mL volumetric flask, which, when diluted to mark with deionized water, will give a final concentration of 1.7 × 10-5 M. Show your calculation setup.
What is the concentration in units of grams of dye per liter of solution ,of the dilute dye solution that is produced as follows? transfer 19.53 ml of stick solution (6.10g/L) to a 200.0Ml volumetric flask and dilute to the 200 ml line with deionized water. Correct number of significant figs
5.00 mL of stock solution is diluted to 25.00 mL, producing solution ALPHA. 10.00 mL of solution ALPHA is diluted to 25.00 mL, resulting in solution BETA. 10.00 mL of solution BETA is then diluted to 25.00 mL, producing solution GAMMA. dilution factor for ALPHA from stock solution = 0.167 dilution factor for BETA from ALPHA solution = 0.0476 part c and d?