If M = 9.0 kip-ft, find the magnitude of the bending stress at a point 2.72 in. above the bottom surface of the beam. The moment of inertia about the z axis is 124.9 in.4, and the centroid of the section is located 4.7 in. above the bottom surface of the beam. M 2207 psi 1712 psi 2368 psi 1971 psi 1860 psi M 1 in. in. H 1 6 in. t 8 in. 1 in.

If M = 9.0 kip-ft, find the magnitude of the bending stress at a point 2.72 in. above the bottom surface of the beam. The moment of inertia about the z axis is 124.9 in.4, and the centroid of the section is located 4.7 in. above the bottom surface of the beam. M 2207 psi 1712 psi 2368 psi 1971 psi 1860 psi M 1 in. in. H 1 6 in. t 8 in. 1 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear in kN. 3. Determine the location of Neutral Axis, in mm, from the top of the section. 4. Determine the location of the centroid, in mm, from the left of the section. 5. Determine the moment of inertia of the section in x106 mm4 . 6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa. 7. Determine the maximum flexural stress experienced by the beam in MPa. 8. Determine the maximum shearing stress in MPa at Neutral Axis. 9. Determine the spacing of rivets in mm. 10. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the bottom of the beam on a section 2.89 feet to the right of B if P = 2314 lb, Q = 8345 lb, w = 1.33 in, L = 7.92 in, b = 3.85 in, and h = 1.41 in. Round off the final answer to two decimal places.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P=1623N, T=4552Nm, a=0.77m, b=1.13m, c=0.78m, w=39mm, and h=80mm. Round off the final answer to five decimal places. Show your complete solution.
A beam is subjected to equal bending moments of Mz = 57 kip·ft. The cross-sectional dimensions are b1 = 8.3 in., d1 = 1.4 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.4 in., and d3 = 1.7 in. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the top of the beam on section 2.72 feet to the right of B if P = 1082 lb, Q = 4244 lb, w = 0.76 in, L = 8.94 in, b = 3.78 in, and h = 0.66 in. Round off the final answer to two decimal places.
A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are b1 = 6.5 in., d1 = 1.5 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.6 in., and d3 = 1.8 in. Determine:(a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative.(c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative.(d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. The cross-sectional dimensions of the beam are also shown. a.Determine the centroid location (measured upward from the bottom), in mm rounded to the nearest tenths. b.Determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures. c. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures. d. Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures.
The proposed shaft is guided in rotation by two roller bearings O and C. T1 = 60 Ib T2 = 400 Ib Reactions: Ro = 293,25 Ib Rc = -178,25 Ib 1) Calculate the torsional stress of the shaft 2) Calculate the bending stress of the shaft
Consider that the section is transmitting a positive bending moment about the z axis,Mz, where Mz=10 kip*in if the dimensions of the section are given in ips units, or Mz=1.13kN*m if the dimensions are in SI units. Determine the resulting stresses at the top and bottom surfaces and at every abrupt change in the cross section. Find the second moment of area, the location of the neutral axis, and the distances from the neutral axis to the top and bottom surfaces.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
A shaft is made of a polymer having an elliptical cross section. If it resists an internal moment of M = 50 N # m, determine the maximum bending stress in the material (a) using the flexure formula, where Iz = 1 4 p(0.08 m)(0.04 m)3, (b) using integration. Sketch a three-dimensional view of the stress distribution acting over the cross-sectional area. Here Ix = 1 4 p(0.08 m)(0.04 m)3.
Determine internal shear force, internal bending moment and internal normal force at point c